User manual JRC NSVS1207

[. . . ] 2007 JRC SAW FILTER NSVS1207 Application 1575. 42MHz GPS Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Typical Input and Output Impedance 50 Nominal Center Frequency (f0) 1575. 42MHz Insertion Loss 1574. 42~1576. 42MHz 1. 6dB max. 1. 1dB Response Variation 1574. 42~1576. 42MHz 0. 8dB max. [. . . ] 1 0 3 Marking (1) Index Mark (2) Part Number Mark (3) Lot Number Shown in Table. 3 Pin no. 70 Max. Fig. 2 Package dimensions (in mm) 2 20 . 1. 80 4 0 65 -. Fig. 3 Desirable land area (in mm) Table. 3 Lot Number Code·i Year/Month·j Month 1 2 3 4 Year 2006 A B C D 2007 N P Q R 2008 a b c d 2009 n p q r Recur every 4 years 5 E S e s 6 F T f t 7 G U g u 4- 0. 10 . 4 8 H V h v 9 J W j w 10 K X k x 11 L Y i y 12 M Z m z NSVS1207 Mar. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. [. . . ] Japan Radio Company does not assume any liability for the case using the products with the application required high reliability or safety extremely (such as space equipment, sea-bottom equipment, medical equipment etc). When intending to use any our product please contact our sales representatives in advance. NSVS1207 Mar 2007 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 0 S21 33pF FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 10 2 (1) 13. 30±0. 20 20 (a) (b) (C) (1. 26±0. 13) 4 (2) 30 6 40 50 CH1 : center 1575. 42 span 200 CH2 : center 1575. 42 span 200 J4Y1 VS971 S11 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z S11 (0. 76) 11 9 (2. 54) (2. 54) 11 9 S22 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 1475. 4 Frequency [MHz] VSWR 7 5 3 1 1475. 4 (2. 54±0. 15) 1675. 4 (1. 4) [12×] Frequency [MHz] Pin No. Connection 1 1675. 4 GND(PKG) 2 GND(PKG) 3 4 5 6 7 8 GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) (0. 8) 0 InsertionLoss [dB] 10 12 20 1 2 3 4 5 (2. 54±0. 15) 30 11 10 40 50 0 9 8 7 6 [12 ×] S21 9 10 11 12 (R0. 3) [12×] 3000 Frequency [MHz] Fig. 2 Package dimensions(in mm) Japan Radio Co. , Ltd. Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]