User manual JRC NSVS1240

[. . . ] 2008 JRC SAW FILTER NSVS1240 Application 915MHz ISM Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Input and Output Impedance 50 Nominal Center Frequency (f0) 915MHz Insertion Loss 902. 0~928. 0MHz 4. 0dB max. 3. 0dB Response Variation 902. 0~928. 0MHz 2. 0dB max. [. . . ] 80) 5 Marking (1) Lot Number (a) Year (b) Month *Oct. --Nov. --Dec. --(c) Date *1-9--10-19--20-31--(2) Part Number Mark 1. 5 3) [ 4 x] Fig. 2 Package dimensions (in mm) 3. 8 0. 93 Pin no. 1 2 3 4 5 6 Connection GND IN GND GND OUT GND 2. 2 1. 15 3. 8 0. 6 1. 15 0. 93 Fig. 3 Desirable land area (in mm) NSVS1240 Oct. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 5 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. As it might be a cause of degradation or destruction to apply D. C. [. . . ] When intending to use any our product please contact our sales representatives in advance. NSVS1240 Oct. 2008 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 0 S21 33pF FREQUENCY CHARACTERISTICS *murata LQW18A series 0 Insertion Loss [dB] 10 2 (1) 13. 30±0. 20 20 (a) (b) (C) (1. 26±0. 13) 4 (2) 30 6 40 50 J4Y1 VS971 S11 6. 5±0. 20 8 10 CH1 : center 915 span 200 CH2 : center 915 span 200 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number (a) Year 2. 0 max. (b) Month *Oct. --- X Nov. --- Y Dec. --- Z S11 (0. 76) 11 9 (2. 54) (2. 54) 11S22 9 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 815 Frequency [MHz] 1015 VSWR 7 5 3 1 815 (2. 54±0. 15) (1. 4) [12×] Frequency [MHz] Pin No. Connection 1 2 3 4 5 6 7 8 1015 GND(PKG) GND(PKG) 0 [12 ×] S21 1 2 3 4 5 (0. 8) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) InsertionLoss [dB] 20 12 40 (2. 54±0. 15) 60 11 10 80 100 0 9 8 7 6 9 10 11 12 (R0. 3) [12×] 3000 Fig. 2 Package dimensions(in mm) Frequency [MHz] Japan Radio Co. , Ltd. Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]