User manual JRC NSVS783

[. . . ] 2004 JRC SAW FILTER NSVS783 Application 1575. 42MHz GPS Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Typical Input and Output Impedance 50 Nominal Center Frequency (f0) 1575. 42MHz Insertion Loss 1574. 42~1576. 42MHz 3. 5dB max. [. . . ] 1 2 3 4 5 6 7 8 Connection GND IN, Unbalanced GND GND OUT, Balanced GND OUT, Balanced GND 1 . 1 5 ±0 . 1 5 (0 . 55) 2 (1 . 2 ) 6 1 7 (0. 75) [6x] (0 . 5 3) [4x] 8 Fig. 2 Package dimensions (in mm) 1. 15 0. 93 3. 8 0. 6 1. 15 3. 8 0. 6 Via -Hole( 0. 3) 0. 93 Fig. 3 Desirable land area (in mm) [4 x ] NSVS783 Oct. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -40ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. As it might be a cause of degradation or destruction to apply D. C. voltage between each terminal, apply D. C. This specification specifies the quality of this component as a single unit. [. . . ] 2004 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW 1 , T *27nH 0 S21 , P , Q , R , S 33pF FREQUENCY CHARACTERISTICS *murata LQW18A series 0 1 : 1574. 42 [MHz] 2. 37 [dB] Insertion Loss [dB] 10 Fig. 1 circuit : 1576. 42 [MHz] 2. 39 [dB] 2 2 (1) 13. 30±0. 20 20 (a) (b) (C) 2 (1. 26±0. 13) 4 (2) 30 6 40 50 CH1 : center 1575. 42 span 200 CH2 : center 1575. 42 span 200 J4Y1 VS971 S11 1 2 6. 5±0. 20 8 10 (3) S22 (R0. 3) [4×] Marking (1) Manufacture's Mark (2) Lot Number 1 2 (a) Year (b) Month *Oct. --- X Nov. --- Y Dec. --- Z 2. 0 max. S11 (0. 76) VSWR 11 9 7 5 3 1 1475. 4 (2. 54) (2. 54)11 9 S22 (c) Date 1 --- 0 -9 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark VSWR 7 5 3 1 1475. 4 (2. 54±0. 15) 2 Frequency [MHz] 1675. 4 1 (1. 4) 1 2 Pin No. Connection 1 1675. 4 GND(PKG) 2 3 4 5 6 7 8 GND(PKG) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) [12×] Frequency [MHz] (0. 8) 0 InsertionLoss [dB] 10 20 30 40 50 0 12 1 2 3 4 5 (2. 54±0. 15) 11 10 9 8 7 6 [12 ×] S21 9 10 11 12 (R0. 3) [12×] 3000 Fig. 2 PackageFrequency [MHz] mm) dimensions(in Japan Radio Co. , Ltd. Insertion Loss [dB] 2 Measuring 1 [. . . ]