User manual JRC NSVS851

[. . . ] 2005 JRC SAW FILTER NSVS851 Application 690. 569MHz Data Communications Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig. 1. Electrical Specifications Item Nominal Center Frequency (f0) Insertion Loss at f0 Loaded Q Attenuation f0±2MHz Insertion Phase 690. 569MHz Turnover Temperature Phase Slope Frequency Temperature Coefficient Substrate Material (at Room Temperature) Spec. [. . . ] Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -30ºC or more than +85ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max. , the time of soldering: 10 seconds max. , the power of soldering iron: 30W max. . Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand. Note 1. This specification specifies the quality of this component as a single unit. Make sure that this component is evaluated and confirmed against this specification when it is mounted to your products. [. . . ] 2005 IN 50 O *27nH 11 10 , X , W , U , V OUT 50 O 39pF 12 SAW , P , Q , , T R *27nH , S 33pF FREQUENCY CHARACTERISTICS 0 *murata LQW18A series 0 Insertion Loss [dB] 20 2 (1) 13. 30±0. 20 40 (a) (b) (C) (1. 26±0. 13) (2) 4 60 6 80 100 CH1: Center 690. 569 Span: 10 CH2: Center 690. 569 Span: 10 0 (3) (R0. 3) [4×] Marking J4Y1 VS971 6. 5±0. 20 8 10 180 Insertion Loss [dB] 2 (1) Manufacture's Mark (2) Lot Number (a) Year 90 *Oct. --- X Nov. --- Y 0 6 (c) Date Dec. --- Z (0. 76) (2. 54) (2. 54) 1 --- 0 -9 -90 8 10 -19 --- 1 20 -31 --- 2 (3) Part Number Mark -180 10 CH1: Center 690. 569 Span: 1 (2. 54±0. 15) CH1: Center 690. 569 Span: 1 (1. 4) [12×] Pin No. Connection 1 2 GND(PKG) GND(PKG) GND(PKG) GND(PKG) OUT/IN GND(signal) GND(PKG) GND(PKG) GND(PKG) GND(PKG) IN/OUT GND(signal) (0. 8) S11 12 (2. 54±0. 15) S22 1 2 3 4 5 [12 ×] 3 4 5 6 7 8 11 10 9 8 7 6 9 10 11 12 (R0. 3) [12×] Fig. 2 Package dimensions(in mm) Phase [deg] 2. 0 max. 4 (b) Month Insertion Loss [dB] Fig. 1 Measuring circuit [. . . ]