User manual JUNIPER NETWORKS JUNOSE 11.0.X MULTICAST ROUTING CONFIGURATION

[. . . ] JUNOSeTM Software for E SeriesTM Broadband Services Routers Multicast Routing Configuration Guide Release 11. 0. x Juniper Networks, Inc. 1194 North Mathilda Avenue Sunnyvale, California 94089 USA 408-745-2000 www. juniper. net Published: 2009-12-29 Juniper Networks, the Juniper Networks logo, JUNOS, NetScreen, ScreenOS, and Steel-Belted Radius are registered trademarks of Juniper Networks, Inc. in the United States and other countries. JUNOSe is a trademark of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. [. . . ] Example host1:boston(config)#router pim Use the no version to remove PIM from the VR. See router pim. Resetting PIM Counters and Mappings You can use the clear ip pim commands to reset PIM counters and mappings. clear ip pim auto-rp Removing PIM 109 JUNOSe 11. 0. x Multicast Routing Configuration Guide Use to clear the group-to-RP router mappings that the router learned through auto-RP. Specify the IP address of an RP to clear the group-to-RP mappings for a particular RP. If you do not specify an IP address, the router clears the group-to-RP mappings on all RP routers learned through auto-RP. Example host1#clear ip pim auto-rp 192. 34. 56. 7 There is no no version. See clear ip pim auto-rp. clear ip pim interface count Use to clear the counters for multicast packet statistics on all interfaces or a specified interface. Specify an interface type and specifier, such as atm 3/0, to clear the counters on that interface. For details about interface types and specifiers, see Interface Types and Specifiers in JUNOSe Command Reference Guide. If you do not specify an interface, the router clears the counters on all interfaces. Example host1#clear ip pim interface atm 3/0. 5 count There is no no version. See clear ip pim interface count. clear ip pim remote-neighbor count Use to clear the counters for remote neighbor statistics on all interfaces or the specified interface. Specify the IP address of an interface to clear the counters for that interface. If you do not specify an interface, the router clears the counters on all interfaces. Example host1#clear ipv6 pim remote-neighbor 1001::1 count There is no no version. See clear ip pim remote-neighbor count. Monitoring PIM You can display information about PIM events and parameters. 110 Monitoring PIM Chapter 3: Configuring PIM for IPv4 Multicast Monitoring PIM Events You can use the debug PIM commands to view information about PIM events. debug ip pim Use to show information about the selected event. To control the type of events displayed, specify a severity level. To control how much information to display, specify a verbosity level. Example host1#debug ip pim events severity 1 verbosity low Use the no version to disable the display. See debug ip pim. undebug ip pim Use to turn off the display of information previously enabled with the debug ip pim command. Example host1#undebug ip pim events There is no no version. [. . . ] Field descriptions Monitoring PIM 237 JUNOSe 11. 0. x Multicast Routing Configuration Guide Group--Multicast group RP--RP router for the multicast group priority--This field is not functional via--Method by which the RP router was assigned (static, BSR) Example host1:2#show ipv6 pim rp-hash 232. 1. 1. 1 Group(s) ff00::/12 RP ::122:1, priority 0, via static See show ipv6 pim rp-hash show ipv6 pim sparse-mode sg-state Use to display information for each (S, G) entry for PIM sparse mode and PIM SSM. Field descriptions Group-to-RP mapping--IPv6 addresses and network mask of the multicast group RP--IPv6 address of RP router SSM group--Indicates that this is an SSM group RPF route--IPv6 address and network mask of the RPF route IIF--IPv6 address of the incoming interface for the RPF route UpNbr--IPv6 address of the upstream neighbor Oifs--Outgoing interface Register Oif to RP--IP address of RP router for the outgoing interface; suppressed for SSM Address--IPv6 address of outgoing interface Interface--Type and specifier of the interface. For details about interface types and specifiers, see Interface Types and Specifiers in JUNOSe Command Reference Guide. Joined as--Type of mapping (S, G)--Mapping from a specific source to a specific group (*, G)--Mapping from any source to a specific group (*, *, RP)--Mapping from any source to any group Join expires--Number of seconds before the (S, G) membership expires Count of entries--Total count of (S, G) pair mappings Example 238 Monitoring PIM Chapter 7: Configuring PIM for IPv6 Multicast host1:2#show ipv6 pim sparse-mode sg-state PIM SM route table and oif information <*, ff0e::1:3> Group-to-RP mapping: ff00::/12 RP: ::123:1 RPF Route: ::123:1/96 IIF: :106:73 UpNbr: ::106:37 Oifs: Address: ::78:7:7 Interface: loopback7 Local group membership present. [. . . ]