User manual JUNO JDK 9582 X

[. . . ] · The hood should not be used by children or persons not instructed in its correct use. MAINTENANCE · Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. · Clean and/or replace the Filters after the specified time period. · Clean the hood using a damp cloth and a neutral liquid detergent. GB 11 CHARACTERISTICS Dimensions 260 126 63 300 MIN. 870-MAX. 1200 60 490 81 41 598-89 8-1198 Components 15 14. 1 7. 3 12a 7. 2. 1 11 Ref. 1 2 2. 1 2. 2 9 14. 1 15 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange ø 150-120 mm 2 Air Outlet Connection Extension 1 Air Outlet Connection 9 2. 1 2 2. 2 12c Ref. [. . . ] 1 2 2. 1 2. 2 9 14. 1 15 Q. ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange ø 150-120 mm 2 Air Outlet Connection Extension 1 Air Outlet Connection 9 2. 1 2 2. 2 12c Ref. Q. ty Installation Components 7. 2. 1 2 Upper Chimney Section Fixing Brackets 7. 3 1 Air Outlet Connection Support 11 6 Wall Plugs 12a 6 Screws 4, 2 x 44, 4 12c 6 Screws 2, 9 x 9, 5 Q. ty Documentation 1 Instruction Manual 1 Warranty 11 12a 1 GB 740 12 INSTALLATION Wall drilling and bracket fixing 1÷2 11 12a 650 min. 116 116 320 Wall marking: · Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. · Draw a horizontal line at 650 mm above the hob. · Place bracket 7. 2. 1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line. · Mark the wall at the centres of the holes in the bracket. · Place bracket 7. 2. 1 on the wall as shown at X mm below the first bracket (X = height of the upper chimney section supplied), aligning the centre (notch) with the vertical line. · Mark the wall at the centres of the holes in the bracket. · Mark a reference point as indicated at 116 mm from the vertical reference line and 320 mm above the horizontal reference line. · Repeat this operation on the other side. · Drill ø 8 mm holes at all the centre points marked. Medium speed, suitable for most operating conditions given the optimum treated air flox/noise level ratio. Maximum speed, used for eliminating the highest cooking vapour emission, including long periods. GB 15 MAINTENANCE Grease filters CLEANING METAL SELF- SUPPORTING GREASE FILTERS · The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. · Remove the filters one at a time by pushing them towards the back of the group and pulling down at the same time. · Wash the filters, taking care not to bend them. · When refitting the filters, make sure that the handle is visible on the outside. Activated charcoal filter (Recirculation version) REPLACING THE ACTIVATED CHARCOAL FILTER · The filter is not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently for particularly heavy usage. · Remove the metal grease filters · Remove the saturated activated carbon filter by releasing the fixing hooks · Fit the new filter by hooking it into its seating · Replace the metal grease filters. GB 16 Lighting LIGHT REPLACEMENT 40 W incandescent light. · Remove the screw fixing the Lighting support. · Extract the lamp and replace with another of the same type. · Replace the lighting support. 20 W halogen light. · Remove the 2 Screws fixing the Lighting support, and pull it out of from the Hood. [. . . ] · Replace the lighting support. 20 W halogen light. · Remove the 2 Screws fixing the Lighting support, and pull it out of from the Hood. · Extract the Lamp from the Support. · Replace with another of the same type, making sure that the two pins are properly inserted in the lamp holder socket holes. [. . . ]