User manual JUNO JDK4530E

[. . . ] · Never use the hood for purposes other than for which it has ben designed. · Never leave high naked flames under the hood when it is in operation. · Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. · Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. [. . . ] · Drill ø 8 mm holes at all the centre points marked. · Insert the wall plugs 11 in the holes. · Fix the lower bracket 7. 2. 1 using the 12a screws (4, 2 x 44, 4) supplied. · Fix the upper bracket 7. 2. 1 and the air outlet connection support 7. 3 together using the 2 screws 12a (4, 2 x 44, 4) supplied. · Insert the two screws 12a (4, 2 x 44, 4) supplied in the hood body fixing holes, leaving a gap of 56 mm between the wall and the head of the screw. GB X 7. 2. 1 13 Mounting the hood body · Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. · Hook the hood body onto the screws 12a · Fully tighten support screws 12a · Adjust screws Vr to level the hood body. Vr 12a Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. · To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. · Fix the pipe in position using sufficient pipe clamps (not supplied). · Remove any activated charcoal filters. ø 150 9 ø 120 RECIRCULATION VERSION AIR OUTLET · Put connection 15 into the connection support 7. 3. · Insert the connection extension pieces laterally 14. 1 in connection 15. · Make sure that the outlet of the extension pieces 14. 1 is horizontally and vertically aligned with the chimney outlets. · Connect the air outlet connection 15 to the hood body outlet using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. · Ensure that the activated charcoal filters have been inserted. ELECTRICAL CONNECTION · Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. 14. 1 15 ø 150 GB 14 Flue assembly Upper exhaust flue · Slightly widen the two sides of the upper flue and hook them behind the brackets 7. 2. 1, making sure that they are well seated. · Secure the sides to the brackets using the 4 screws 12c (2, 9 x 9, 5) supplied. · Make sure that the outlet of the extensions pieces is aligned with the chimney outlets. 2 7. 2. 1 12c 2. 1 Lower exhaust flue · Slightly widen the two sides of the flue and hook them between the upper flue and the wall, making sure that they are well seated. · Fix the lower part laterally to the hood body using the 2 screws 12c (2, 9 x 9, 5) supplied. 2. 2 12c USE Control panel L S L S V1 V2 V3 Light Led Motor Speed Intensive V1 V2 V3 Switches the lighting system on and off. Switches the extractor motor on and off at low speed. Used to provide a continuos and silent air change in the presence of light cooking vapours. Medium speed, suitable for most operating conditions given the optimum treated air flox/noise level ratio. [. . . ] · Replace the Support, fixing it in place with the two Screws removed as above. GB 17 Quest'apparecchio è conforme alla norma europea sulla bassa tensione C. E. E. 73/23 relativa alla sicurezza elettrica e alle norme europee: C. E. E. 89/336 relativa alla compatibilità elettromagnetica e C. E. E. This appliance conforms to European Low Voltage Directive 75/23/CEE governing electrical safety, European Directive 89/ 336/CEE on Electromagnetic Compatibility and Directive 93/68/CEE regarding CE Marking. [. . . ]