User manual JUNO JDK5535-EF

[. . . ] 3. 3 - Connect the cooker hood to the mains via a double pole switch which has 3 mm clearance between the contacts. 3. 5 - When istalled, the hood must be positioned at least 65 cm above a cooking appliance. 3. 6 - Never do flambé cooking under this cooker hood. 3. 7 - Never leave frying pans unattended during use as overheated fats and oils may catch fire. [. . . ] If the splashback is to be fixed to the wall using both the top and bottom fixing holes care must be taken to ensure that the splashback is fitted at the correct height before fixing it into position. The fitting should be undertaken by a competent person with experience in this type of installation. If the splashback is to be fixed through only the top fixing holes proceeds as follows: a - Put the splashback on the worktop as illustrated in Fig. 2a; then holding it against the wall to ensure that it is correctly positioned mark the holes for the top fixing screws on the wall. b - Pilot drill the wall using an 8 mm drill and fix the splashback using the 8 mm rawl plugs and screws supplied. c - If the fixing holes in the bottom of the splashback are not to be used to secure the splashback to the wall the installer should ensure that the bottom edge is tucked down behind the rear of the worktop. 3) Adjust the two screws V (on the canopy connection points) to approximately half way. Hook the rear of the canopy to the wall bracket 1, after anchoring the latter to the wall. Turn the screws V to adjust the canopy vertically and level it horizontally. Fit and lock the central fixing screw V1 (provided) to lock the canopy in place. 4. 3 - Electrical connection and working test 1 - The safety measures 3. 2, 3. 3 and 3. 4 of paragrapf 3 are to be strictly observed. 2 - Once the electrical connection has been completed, check that worktop illumination, motor and speed work properly. 7 4. 4 - Ducting or Recirculation fitting 1 - Ducting fitting a - The cooker hood can be ducted to the outside using either rigid or flexible fire retardant ducting of 120 mm. b - The installer should provide suitable ducting and sealing material for the installation. The cooker hood can also be ducted to the outside through one of the rectangular openings located in either side of the lower section of the chimney stack (Fig. c - If the hood is provided with the charcoal filters fitted, the filters should be removed (see paragraph 3. 2 part 2a). 2 - Recirculation fitting a - The filtered air is returned to the room through the two side grilles on the U-shaped lower section I, which are either formed in the metal itself. b - Fix the metal plug T onto the bottom half-pipe I using the two screws provided (Fig. 4. 5 - Fitting the telescopic chimney stack (Fig. 6) To fit the upper section item S first expand the chimney slightly to allow it to fit over the wall brackets 2 and then secure the upper section using the 4 screws supplied. The lower section item I of the chimney stack should be fitted between the lower bracket 2 and the wall, paying attention to fit the lower part of the section into the recess of the canopy. To fit the lower section I to the ducting spigot using the two remaining self tapping screws. NOTE - The upper S and lower I sections are fixed to the wall brackets 2 through a spring and the connection is made by pushing both sections vigorously toward the centre. Part 2a - OPERATION AND MAINTENANCE INSTRUCTIONS 1 - Safety warnings It is most important that all the warnings shown in paragraph 3 of the Installation Instructions are strictly observed. Moreover, pay special attention to the following warnings during the use and maintenance of the cooker hood: The grease filters and the charcoal filter should be cleaned or replaced as recommended by the manufacturer or more frequently if the hood is used consistently over 4 hours per day. [. . . ] 3. 3 - Lighting a - Two 40W lamps ensure the worktop lighting. These lamps can be reached by removing the metal grease filters. b - Should the two lamps fail to work, open the metal grid and ensure they are correctly screwed into the holder. c - When changing the lamp, an identical replacement must be fitted to ensure the safe working of the cooker hood. [. . . ]