User manual JUNO JDS2720W

[. . . ] Algemeen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Generalidades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Informaes Gerais . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Componenti . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Mantenimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manuteno . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filtri antigrasso metallici Metal grease filters Filtres graisses mtalliques Metall-Fettfilter Metalen antivet-filter Filtro antigrasa metlicos Filtros metlicos antigordura Filtri al carbone attivo Active carbon filter Filtre au charbon actif Aktiv-Kohlefilter Aktief koolfilter Filtro de carbn activo Filtros de carvo activo Illuminazione Lighting Eclairage Beleuchtung Verlichting Iluminacin Iluminao 8 14 20 27 33 39 45 8 14 20 27 33 39 45 8 14 20 27 33 39 45 Pulizia Cleaning Nettoyage Pflege Reiniging Limpieza Limpeza 3 Part 1 - INSTALLATION INSTRUCTIONS 1 - GENERAL INFORMATION This canopy hood is designed to be fixed to any rigid vertical surface, over a gas or electric hotplate and can be used either in the extraction mode (ducted to the outside) or in the recirculation mode (internal recycling). Before commencing the installation, consideration should be given to the difficulties to be found during installation and to the bulky weight of the hood. The installation work must be undertaken by a qualified and competent person in conformity to the rules concerning the evacuation of contaminated air. The manufacturer disclaims all liability for any damage or injury caused as a result of not following the instructions for installation contained in the following text. 2 - COMPONENTS The cooker hood is made up of the following components (fig 1): 2. 1 - n. 1 hood canopy C complete with controls, lighting and fan motor. 1 telescopic chimney stack formed by: n. 1 U-shaped lower section item I 2. 3 - n. 2 recirculation venting grilles item G (special versions only) 2. 4 - n. 1 deflector D (special versions only) 2. 7 - n. Minor adjustments can be made using the hood regulating screws (see below). Mark the centres of the two eyelet holes of the bracket on the wall. 3 - Fixing the wall brackets item 2: a) Place one of the two brackets (item 2 fig. 1) 1 or 2 mm from the ceiling or from a horizontal line drawn between the top of the adjoining wall cabinets, ensuring that the bracket is level. b) Mark the centres for the keyhole bracket fixing screws. c) Place the other wall bracket (item 2 fig. 1) on the wall at "X" distance. This measurement should be determined by the height of the upper chimney stack. 11 Part 2 - USE AND MAINTENANCE INSTRUCTIONS d) Mark the centres for the keyhole bracket fixing screws. 4 - Pilot drill all the hole positions as marked on the wall using an 8 mm drill and fix the wall brackets 1-2 using the rawl plugs and screws supplied. 5 - Splashback (optional) When a splashback is to be fitted, the distance between the cooker hood and the cooking appliances will be determined by the height of the splashback, item F. [. . . ] 6) a) The filtered air is returned to the room through the two side grilles on U-shaped lower section I as a plastic insert. b) Fit the recirculation spigot item R into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. c) Fit the additional spigot, item P, into the round outlet on top of the canopy while pressing down on the spigot until it snaps into position. Then fit the recirculation spigot R into the top of the spigot , item P, and install the charcoal filters inside the canopy as instructed in paragraph 3. 3 2 part 2a). [. . . ]