User manual JUNO JKG 7485

[. . . ] JKG 7485 GEBRAUCHSANWEISUNG OPERATING INSTRUCTIONS MODE D'EMPLOI GEBRUIKSAANWIJZING 2222 147-62 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 11 12 12 12 12 12 14 14 14 14 14 14 15 15 15 16 16 16 17 17 17 17 17 Installation . Positioning . Electrical connection . Cleaning the interior . Instructions for totally built-in appliances . [. . . ] The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. D023 min. cm 2 For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. 200 D027 Fig. 2 A Push appliance into housing until stop strip (A) touches the kitchen unit. Fig. 3 This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. A Cleaning the interior D265 Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. If after having carried out the operation described in section 2 there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). 12 Fig. 8 Open the door and push the appliance against the side of kitchen furniture opposite to that of appliance hinges. D Fasten the appliance with 4 screws provided in the kit included with the apC D723 pliance. Snap vent grill (C) and hinge cover (D) into position. Fig. 5 8mm PR34 Open both the appliance door and that of the kitchen unit to approx. Place the little plates over the runners. Hold the doors of the appliance and the unit together and mark the holes. Fig. 9 Press in the joint covers between the appliance and the kitchen furniture. D724 Fig. 6 Remove the little plates and make the holes with a diam. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, PR35 if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. If the appliance is to be fitted laterally to the kitchen unit, it will be sufficient to loosen the screws of the little plates (D), move them as shown in Fig. [. . . ] Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. Do not use a mechanical device or any artificial means to speed up the thawing process other than those recommended by the manufacturer. However, when the ice becomes very thick on the inner liner, complete defrosting should be carried out as follows: pull out the plug from the wall socket or turn the thermostat knob to the «O» setting; remove any stored food, wrap it in several layers of newspaper and put it in a cool place; leave the door open, and insert the plastic scraper in the appropriate seating at the bottom centre, placing a basin underneath to collect the defrost water; Fig. 14 Ice-cube production This appliance is equipped with one or more trays for the production of ice-cubes. [. . . ]