User manual JUNO JKU6431

[. . . ] JKU 6031 JKU 6431 GEBRAUCHSANWEISUNG OPERATING INSTRUCTIONS MODE D'EMPLOI GEBRUIKSAANWIJZING 2222 319-32/1 CONTENTS Warnings . . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page . page 13 14 14 14 14 15 15 15 17 18 18 18 18 18 18 19 19 19 20 21 21 21 21 21 Installation . Positioning . Electrical connection . . Door reversibility Fitting a decorative door panel. Changing the opening direction of the door . [. . . ] Do not use detergents or abrasive powders, as these will damage the finish. 14 Location Fig. 4 600 547 550 This appliance is designed to be built-in to a space having the dimensions given in Fig. 1. Take the hinge removed from the upper part of the appliance on the opposite side (see Fig. 4), and, using the s c re w s r e m o v e d from the lower part, fix it to the base of the appliance itself. D510 820 820-870 59 6 D506 100-170 870 Fig. 2 The height of the appliance can be altered if required by means of adjustable feet situated at its base (Fig. 2). Remove and refit the other hinge on the upper part of the appliance on the opposite side. Fix the two front screws into the upper and lower hinges (Fig. Finally, check the alignment of the door and make sure it closes properly. After having reversed the opening direction of the door, discard the original plastic insert removed and fit the insert supplied with the appliance on the opposite side. Fitting a decorative door panel D507 Door reversibility Remove the two screws which fix the upper hinge to the door. Fig. 3 Carefully lean the appliance on its back and remove the plastic insert (Fig. 3). Important: The components needed to fit the decorative panel have been pre-fitted on the appliance. The brackets are secured to the panel by means of the 7 Ø 3. 5x13 screws supplied. Before starting to fit the panel, remove the large top bracket by unscrewing the screws and adjusting pins pre-fitted on the appliance door. The small bottom bracket need not be removed. Fig. 5 A = = D447 Remove the two screws which fix the lower hinge to the door. Remove the four screws which fix the lower hinge to the base of the appliance and remove the hinge itself; be very careful to recover all the screws. Remove the four screws that fix the upper hinge to the appliance and remove the hinge itself. D467 Place the appliance in the position where it is to be built in (Fig. The appliance is fitted with adjustable feet; screw the front and rear feet in or out to adjust the height of the appliance to that of the recess. Keeping the appliance central in the recess, slide it in until its back touches the wall. With a tape measure (or similar instrument), measure distance (A) between the top edge of the door and the top edge of the decorative panel, placing it next to the recess. 15 Fig. 10 = = A -1cm D468 Lay the panel face down (Fig. Position the top bracket on the panel, making sure that there is an equal distance between it and the sides and that its distance from the top edge is equal to distance (A) less 1 cm. Secure the bracket with the screws supplied. Take care not to damage the front face of the panel whilst working. Fig. [. . . ] Do not exceed the storage period indicated by the food manufacturer. Important If there is a power failure when food is in the freezer, do not open the door of the freezer compartment. The frozen food will not be affected if the power cut is of short duration (up to 6-8 hours) and the freezer compartment is full, otherwise, it is recommended that the food should be used within a short time (a temperature increase of the frozen food shortens its safe storage period). 19 Defrosting Frost is automatically eliminated from the evaporator of the refrigerator compartment every time the motor compressor stops, during normal use. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. [. . . ]