User manual JURA ENA 3

[. . . ] en en en Instructions for Use en it The `ENA 3 Instructions for Use' has been awarded the seal of approval by the independent German Technical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects. ENA 3 IMPORTANT SAFEGUARDS These safeguards apply for machines with UL safety test (see rating plate and chapter 8, `Technical data'). Follow the basic safety precautions When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following: Z Read all instructions. Z To protect against fire, electric shock and injury to persons, do not immerse cord, plugs, or body of machine in water or other liquid. Z Close supervision is necessary when any appliance is used by or near children. [. . . ] y T Turn the switch clockwise to position o when there is sufficient milk foam in the cup. HEATING READY appears as soon as the ENA is g T Turn the Rotary Switch until STEAM is displayed. k T Press the Rotary Switch. sufficiently heated. HEATING READY appears as soon as the ENA is STEAM, the milk is foamed by the hot l T Turn the switch to position m. steam. 18 ENA 3 y T Turn the switch to position o when the milk foam has reached the required consistency. E You can prepare more steam within about 40 seconds. k T Press the Rotary Switch. HEATING READY appears as soon as the ENA is sufficiently heated. l T Turn the switch to position m. y T Turn the switch clockwise to position o STEAM, the hot milk is being prepared. when there is sufficient milk in the cup. T Place the cup under the coffee spout. k T Press the Rotary Switch to start coffee preparation. To ensure that the 2-stage frothing nozzle works perfectly, it should be rinsed regularly (refer to Chapter 4 `Rinse ­ Dismantling and rinsing the 2-stage frothing nozzle'). E 1 CUP, the pre-set amount of water flows You can prepare more hot milk within about 40 seconds. To ensure that the Professional Cappuccino Frother works perfectly, it should be rinsed and cleaned regularly (refer to Chapter 4 `Rinse ­ Professional Cappuccino Frother'). en Heating milk with the 2-stage frothing nozzle Precondition: READY is shown on the display. T Push the 2-stage frothing nozzle to the top position. T Place a cup of milk below the 2-stage frothing nozzle and immerse the nozzle in the milk. Heating milk with the Professional Cappuccino Frother Precondition: READY is shown on the display. T Remove the protective cover from the Professional Cappuccino Frother. T Insert the other end of the milk pipe into a milk carton or connect it to a milk container. T Set the selector lever of the nozzle to the milk t position. en en en E If the nozzle does not reach into the cup, lift the cup towards the nozzle. g T Turn the Rotary Switch until STEAM is displayed. k T Press the Rotary Switch. g T Turn the Rotary Switch until STEAM is displayed. it sufficiently heated. HEATING READY appears as soon as the ENA is 19 ENA 3 l T Turn the switch to position m. Z STEAM, the milk is heated by the hot steam. Temperature: NORMAL, HIGH y T Turn the switch to position o as soon as the required temperature is reached. E You can prepare more steam within about 40 seconds. To ensure that the 2-stage frothing nozzle works perfectly, it should be rinsed regularly (refer to Chapter 4 `Rinse ­ Dismantling and rinsing the 2-stage frothing nozzle'). The following applies when preparing 2 coffees: Z The amount of water set for 1 coffee is dispensed per cup when 2 cups are prepared. Z 2 coffees are always prepared with the coffee strength `mild'. Z 2 coffees are prepared at the same temperature which is set for 1 coffee. Default settings in programming mode always follow the same model. Example: Changing the default setting for the strength of one coffee from NORMAL to Hot water E To prepare hot water, attach either the hot water nozzle or the 2-stage frothing nozzle to the Connector System©. STRONG. CAUTION There is a danger of scalding from hot water splashes. Precondition: READY is shown on the display. y T Turn the switch clockwise when there is sufficient water in the cup. J Precondition: READY is shown on the display. T Open the cover behind the Rotary Switch. [. . . ] `Rinse ­ Rinsing the nozzle'). The nozzle does not produce enough milk foam. The nozzle is either in the wrong position or is dirty. T Adjust the position of the nozzle (refer T Rinse the nozzle (refer to Chapter 4 Coffee only drips out during preparation. Coffee or pre-ground coffee has been ground too finely and is blocking the sieve. The CLARIS filter cartridge is activated. The grinder is not yet completely filled with beans. If the device is exposed to the cold for a long period of time, the heating function is disabled for safety reasons. [. . . ]