User manual JVC AV-14FN14 Instruction Manual

[. . . ] COLOR TELEVISION AV-14FN14 AV-20NN14 AV-21CN14 AV-21YN14 Contents Knowing your TV's features . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Remote control buttons and basic functions . 3 TV buttons and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Setting up your TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For details, see the manual of your VCR. VHF/UHF outdoor antenna Rear of the TV VIDEO-1 INPUT OUTPUT VIDEO AUDIO To audio/video output To RF output 3 Inserting batteries into the remote control. Insert two batteries by following the ª and · polarities and inserting the · end first. CAUTION: Follow the cautions printed on the batteries. Notes: · Use AA/R6/UM-3 dry cell batteries. · If the remote control does not work properly, install new batteries. The supplied batteries are for testing, not regular use. VCR To antenna input The illustration shown is just a sample. It may not be same as your TV. 2 Connecting the compatible AC plug to the AC outlet. 4 Turn on the TV by pressing the main power button. JVC logo appears on the screen. 6 Setting up your TV (continued) 5 Making the initial settings Set up your TV by pressing MENU/OK button or waiting for 15 seconds, then the TV will operate by following steps as below: AUTO PROGRAM AIR CABLE AUTO PROGRAM SETUP TOUR RESTART? 7 NO OK RESTART · Press 5/ button to select AIR or CABLE, press the MENU/OK button. TV will start searching for the channels. AUTO PROGRAM 22% OK CH 12 · Press the red button to cancel the SETUP TOUR RESTART function. If you want to make initial settings again when the next time you turn on the TV, press the MENU/OK button to activate the SETUP TOUR RESTART function. CHANNEL SUMMARY CH/CC CH02 CH03 CH04 CH05 CH06 CH07 CH08 SKIP To stop AUTO PROGRAM, press MENU/OK button. · To complete the initial setting, press the MENU/OK button. To set undesired channels to be skipped, see page 12. · If the JVC logo does not appear, use AUTO PROGRAM function to make the initial settings. This function is located in the INSTALL menu. · If the JVC logo appears, although you had made the initial settings, press the TV/VIDEO button to exit from initial settings. 7 Basic setting for picture COLOR SYSTEM You can select the appropriate color system when the picture is not clear or no color appears. Press the COLOR SYSTEM button to select a setting. In TV mode: NTSC 3. 58 MHz (Fixed) In VIDEO mode: AUTO PAL SECAM NTSC4. 43 NTSC3. 58 To operate this function with a menu: MENU PICTURE PICTURE FEATURES COLOR SYSTEM For the color system in each country or region, see the table below: Area Country or Region Bahrain, Kuwait, Oman, Qatar, United Arab Emirates, Yemen, etc. Indonesia, Malaysia, Singapore, Thailand, India, etc. Islamic Republic of Iran, Lebanon, Saudi Arabia, etc. System PAL PAL PAL SECAM NTSC SECAM PAL PAL PAL PAL PAL PAL SECAM To operate this function with a menu: PICTURE PICTURE MODE MENU To return the USER setting to the default, press the blue button when the PICTURE SETTING menu appears. Adjusting the picture - USER You can adjust the desired picture setting when selecting USER in PICTURE MODE. 1 Select the USER in PICTURE MODE under PICTURE menu. PICTURE PICTURE MODE MENU USER 2 Select the PICTURE SETTING in PICTURE menu, then adjust the setting. PICTURE PICTURE SETTING MENU PICTURE BRIGHT DETAIL COLOR TINT* 2 : Lower 2 : Darker 2 : Softer 2 : Lighter 2 : Reddish 3 : Higher 3 : Brighter 3 : Higher 3 : Deeper 3 : Greenish Asia, Middle East *TINT can only be adjusted in NTSC system. Europe PICTURE BOOSTER (Except AV-21CN14) You can improve picture clarity when the picture is unclear due to the low signal reception. Press the PICTURE BOOSTER button to select the desired mode. [. . . ] Try to adjust the antenna direction or use a better directionality antenna. · Choose the appropriate color Poor picture system. Refer to "COLOR SYSTEM" on page 8. · Adjust the COLOR or BRIGHT setting. [. . . ]