User manual JVC AV-20NT11 Instruction Manual

[. . . ] COLOR TELEVISION AV-21YT11 AV-20NT11 AV-14FT11 AV-21YN11 AV-20NN11 AV-14FN11 INSTRUCTIONS GGT0006-001A-H 0303-NIC-JMT 2003 VICTOR COMPANY OF JAPAN, LIMITED 2 Thank you for purchasing this JVC color television. To ensure your complete understanding, please read this manual thoroughly before operation. TABLE OF CONTENTS CONNECTIONS Front & Rear Panel Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Indoor Antenna Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Antenna and VCR . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Power button ( There are two methods to turn the power on after turning it off by pressing the POWER button on the remote control or by using the On/Off Timer function: 1) Press the POWER button on the remote control. 2) Press the CHANNEL n button or CHANNEL , button on the TV front panel. When the On-Timer function is set, the On-Timer lamp will light. Even if you turn the power off by pressing the POWER button on the remote control, if the On-Timer function is active the OnTimer lamp stays lit. See page 13 to set On/Off Timer. ADJUSTING VOLUME 1 Press the VOLUME button on the front panel or remote control. The volume level bar will appear. VOLUME 13 |||| ||| ------------------- 2 Press the MUTING button to instantly turn the volume off to zero. To restore the volume to your previous level, simply press the MUTING button again. CHANGING CHANNELS 1 2 10 key direct access. Press the numbers on the remote's 10 key pad. For single-digit channel numbers press 0 then the number. For channels above 100, press the 100+ button plus the 2-digit number. Press the n CHANNEL , button, it will scan the channels in order. NOTE: After you operate the Auto Tuner Setup (page 10), all of the blank or empty, channels will be removed from scanning so that there is no noise or channel snow when you scan, only active channels. Press the release of the RETURN + button to return to the previous channel. Then, select another channel (game #2) with the 10 key pad and push the RETURN+ button to flip directly back and forth. Press and hold down the RETURN + button for three seconds. The message, "RETURN CHANNEL PROGRAMMED !" will appear and you can scan as you wish with the n CHANNEL , button. Press RETURN + button again and you will go back to the Return+ channel you programmed. 3 4 To cancel the Return + channel, press and hold down the RETURN + button for another three seconds and the message, "RETURN CHANNEL CANCELED !" appears. Pressing any number key or turning the TV off will also cancel a Return+ channel. 8 GETTING STARTED SETUP TOUR When the TV is first turned on it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR. In case of resetting that the reason for such as removal, you can set the SETUP TOUR function on the menu. For datails, see page 10. 1 Press the Main power button on the TV. The POWER lamp or POWER/ON TIMER lamp lights. After the JVC logo has been displayed, the TV automatically switches to the language setting mode. [. . . ] operating properly · Maybe you are too far from the TV, you must be within 7m. You cannot select a certain channel · Make sure the channels are programmed. · Perhaps the channel is locked, select it with the 10 key pad and follow instructions, on page 14. The power turns off · Perhaps the On/Off Timer is set, press the POWER button, check page 13. by itself · The power was interrupted or the power cord unplugged. [. . . ]