User manual JVC AV-21D31

[. . . ] COLOR TELEVISION VICTOR COMPANY OF JAPAN, LIMITED AV-21D31 AV-20N31 AV-14F31 AV-21D11 AV-20N11 AV-14F11 INSTRUCTIONS 2001 VICTOR COMPANY OF JAPAN, LIMITED LCT1013-001A-H 0601-Ki-NV-PH 2 Thank you for purchasing this JVC color television. To ensure your complete understanding, please read this manual thoroughly before operation. TABLE OF CONTENTS CONNECTIONS Front & Rear Panel Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Indoor Antenna Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Antenna and VCR . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The On Timer lamp will light when the On/Off Timer is set, even when the TV power is off. When you do not use the television for a long period of time, turn the power off by pressing the Power button ( ) on the TV front panel. There are two methods to turn the power on after turning it off by pressing the POWER button on the remote control or by using the On/Off Timer function: 1) Press the POWER button on the remote control. 2) Press the CHANNEL n button or CHANNEL , button on the TV front panel. When the On-Timer function is set, the On-Timer lamp will light. Even if you turn the power off by pressing the POWER button on the remote control, if the On-Timer function is active the OnTimer lamp stays lit. See page 12 to set On/Off Timer. ADJUSTING VOLUME 1 Press the VOLUME button on the front panel or remote control. The volume level bar will appear. VOLUME 13 |||| ||| ------------------- 2 Press the MUTING button to instantly turn the volume off to zero. To restore the volume to your previous level, simply press the MUTING button again. CHANGING CHANNELS 1 2 10 key direct access. Press the numbers on the remote's 10 key pad. For single-digit channel numbers press 0 then the number. For channels above 100, press the 100+ button plus the 2-digit number. Press the CHANNEL m button, it will scan the channels in order. NOTE: After you operate the Auto Tuner Setup (page 9), all of the blank or empty, channels will be removed from scanning so that there is no noise or channel snow when you scan, only active channels. Press the release of the RETURN+ button to return to the previous channel. Then, select another channel (game #2) with the 10 key pad and push the RETURN+ button to flip directly back and forth. Press and hold down the RETURN+ button for three seconds. The message, "RETURN CHANNEL PROGRAMMED !" will appear and you can scan as you wish with the CHANNEL m button. Press RETURN+ again and you will go back to the Return+ channel you programmed. To cancel the Return+ channel, press and hold down the RETURN+ button for another three seconds and the message, "RETURN CHANNEL CANCELED !" appears. Pressing any number key or turning the TV off will also cancel a Return+ channel. 3 4 8 USING THE MENU INITIAL SETUP ITEMS AUTO TUNER SETUP NOISE MUTING BACKGROUND CLOSED CAPTION LANGUAGE SELECT OPERATE BY BY ON OFF BLACK CLEAR POR SPA ENG USING THIS GUIDE: Throughout this guide there are certain symbols we use as shorthand to show you what to do. When you see them, keep these factors in mind: Up and down arrows mean press the MENU UP or MENU DOWN buttons. Pressing the up or down buttons allows you to: · Move vertically in the main menu screen · Move through a submenu, or · Move to the next letter, number, or other choice in a submenu, or · Back up to correct an error Left and right arrows mean press the MENU LEFT or MENU RIGHT button to: · Select the highlighted item, or · Select the options in a submenu The "Press Button" means you should press that button on the remote control Important information, or a note, about a feature follows a cube like this one. [. . . ] operating properly · Maybe you are too far from the TV, you must be within 7m. You cannot select a certain channel · Make sure the channels are programmed. · Perhaps the channel is locked, select it with the 10 key pad and follow instructions, on page 13. The power turns off · Perhaps the On/Off Timer is set, press the POWER button, check page 12. by itself · The power was interrupted or the power cord unplugged. [. . . ]