User manual JVC AV-28R370KE-AV-28R370 Instruction Manual

[. . . ] Specifications Model AV-32R370KE AV-28R370KE Item Broadcasting systems CCIR I Colour systems PAL · The EXT terminals also support the NTSC 3. 58/4. 43 MHz system. Channels and frequencies E21-E69 Sound-multiplex systems NICAM (I) system Teletext systems FLOF (Fastext), WST (World Standard Text) Power requirements 220 - 240 V AC, 50 Hz Power consumption Maximum: 200 W, Average: 127 W, Maximum: 200 W, Average: 125 W, Standby: 3 W Standby: 3 W Picture tube size Viewable area 76 cm (measured Viewable area 66 cm (measured diagonally) diagonally) Audio output Rated Power output: 10 W + 10 W + 10 W, 18 W (woofer) Speakers (13 cm × 6. 5 cm) oval × 2, (16 cm × 4 cm) oval × 1, 13 cm round woofer ×1 EXT-1 terminal Euroconnector (21-pin, SCART) · Video input, Audio L/R inputs and RGB inputs are available. · TV broadcast outputs (Video and Audio L/R) are available. EXT-2 terminal Euroconnector (21-pin, SCART) · Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available. [. . . ] · This returns the picture settings in the TINT mode you have chosen to the default settings, and stores them in the TINT mode. Picture Adjustment You can change the picture settings of each TINT mode as you like. CONTRAST You can adjust the picture contrast. 2 : lower 3 : higher BRIGHT You can adjust the picture brightness. 2 : darker 3 : brighter SHARP You can adjust the picture sharpness. 2 : softer 3 : sharper COLOUR You can adjust the picture colour. 2 : lighter 3 : deeper 18 Using the TV's menu PICTURE FEATURES COLOUR SYSTEM The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. (1*/, 6+ AUTO VNR VNR Stands for "video noise reduction". AUTO: This mode reduces any "noise" (interference or snowing) in the current picture. The function also adjusts the optimum sharpness of the picture (SHARP). MIN: The AUTO VNR function is cancelled. If you set the mode to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the mode to MIN. However, any noise remaining in the original picture may be emphasized. MAX: This mode always reduces any noise as much as possible, irrespective of state of the picture. When you set the mode to AUTO but still notice some noise, change the mode to MAX. However, this may reduce the sharpness of the picture. 1 Choose COLOUR SYSTEM then press the a button 2 Press the 5 buttons to chose the appropriate colour system. Then press the a button PAL: PAL system SECAM: SECAM system NTSC 3. 58: NTSC 3. 58 MHz system NTSC 4. 43: NTSC 4. 43 MHz system AUTO: This function detects a colour system from the input signal. Only when you are viewing a picture from Programme number PR 0 (AV), or EXT terminal, you can choose using the AUTO function. · The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3. 58 or NTSC 4. 43. 19 Using the TV's menu 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Choose 4:3 AUTO ASPECT then press the a button SOUND SETTING STEREO / I · II When you are viewing a bilingual broadcast programme, you can choose the sound from Bilingual I (Sub I) or Bilingual II (Sub II). [. . . ] In this case, keep the equipment away from your TV. If speakers cause this to happen, use magnetic-shielded speakers instead. · A picture may be tilted due to the earth's own magnetic field. If so, use the "PICTURE TILT (Only for AV32T67SKE)" on page 21 to correct the tilt. [. . . ]