User manual JVC AV-28S2EK

[. . . ] 6SHFLILFDWLRQV Model Item AV28S2EK/AV32S2EK AV28S2EK* CCIR I AV32S2EK* Broadcasting systems Colour systems Channels and frequencies Sound-multiplex systems Teletext systems Power requirements Power consumption Picture tube size Audio output Speakers EXT-1 terminal PAL · The EXT terminals also support the NTSC 3. 58/4. 43 MHz system. E21-E69 NICAM (I) system FLOF (Fastext), WST (World Standard Text) 220 - 240 V AC, 50 Hz Maximum: 168 W, Average: 115 W, Standby: 0. 8 W Viewable area 66 cm (measured diagonally) Rated Power output: 7. 5 W + 7. 5 W (20 cm × 4 cm) oval × 2 Euroconnector (21-pin, SCART) · Video input, Audio L/R inputs and RGB inputs are available. · TV broadcast outputs (Video and Audio L/R) are available. Euroconnector (21-pin, SCART) · Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available. [. . . ] To display the PICTURE SETTING menu: 1 Press the 3 button to display the MENU (main menu) 3 Press the 3 button to complete the settings The menu disappears. 2 Press the ë buttons to choose PICTURE SETTING, and press the 3 button s (&2#02'( When you set the ECO MODE function to ON, the screen contrast is automatically adjusted to a setting suitable for the brightness of your room. This reduces eye strain for you and the amount of power the TV uses. s 7, 17 You can select one of three TINT modes (three kinds of picture settings) to adjust the picture settings automatically. 1 Press the ë buttons to choose TINT 2 Press the ì buttons to choose a mode COOL: A cool white colour base with a boost in the colour and contrast levels that creates a more vivid picture. 1 Press the ë buttons to choose ECO MODE 2 Press the ì buttons to choose ON To cancel the ECO MODE function: Press the ì buttons to choose OFF. WARM: A warm orange/red colour base that creates the appropriate colour and contrast levels for watching films. 3 Press the 3 button to complete the setting The menu disappears. NORMAL: A normal white colour base with normal colour and contrast levels. 3 Press the 3 button to complete the setting The menu disappears. s 3LFWXUH#DGMXVWPHQW You can change the picture settings of each TINT mode as you like. The picture settings changed are stored in the TINT mode. 1 Press the ë buttons to choose an item. 2 Press the ì buttons to change the setting. ï Lower Darker Softer Lighter Reddish Item CONTRAST (picture contrast) BRIGHT (picture brightness) SHARP (picture sharpness) COLOUR (picture colour) HUE (picture hue) î Higher Brighter Sharper Deeper Greenish 4: 3LFWXUH#IHDWXUHV 2 Press the ì buttons to choose the appropriate colour system. PAL: PAL system NTSC 3. 58: NTSC 3. 58 MHz system NTSC 4. 43 NTSC 4. 43 MHz system AUTO: This function detects a colour system from the input signal. You can only use this when you are viewing a picture from programme number PR 0 (AV), or on EXT terminal. To display the PICTURE FEATURES menu: 1 Press the 3 button to display MENU (main menu) 2 Press the ë buttons to choose PICTURE FEATURES, and press the 3 button 3 Press the 3 button to complete the setting The menu disappears. · The AUTO function may not work properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · You cannot choose NTSC 3. 58 or NTSC 4. 43 for programme numbers PR 0 (AV) to PR 99. s $872#915 VNR Stands for "video noise reduction". The AUTO VNR function reduces any "noise" (interference or snowing) in the current picture. The function also adjusts the optimum sharpness of the picture (SHARP). 1 Press the ë buttons to choose AUTO VNR 2 Press the ì buttons to choose AUTO MIN: The AUTO VNR function is cancelled. If you set the mode to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the mode to MIN. However, any noise remaining in the original picture may be emphasized. MAX: This mode always reduces any noise as much as possible, irrespective of state of the picture. When you set the mode to AUTO but still notice some noise, change the mode to MAX. However, this may reduce the sharpness of the picture. s 7=6#$872#$63(&7 You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Press the ë buttons to choose 4:3 AUTO ASPECT. Then press the 3 button The sub-menu of the 4:3 AUTO ASPECT function appears. 3 Press the 3 button to complete the setting. The menu disappears. s &2/285#6<67(0 The colour system is chosen automatically. However, if the picture is not clear or no colour appears, choose the colour system manually. 2 Press the ë buttons to choose a ZOOM mode 3 Press the 3 button to complete the setting The menu disappears. 1 Press the ë buttons to choose COLOUR SYSTEM. Then press the 3 button The sub-menu of the COLOUR SYSTEM function appears. 4; Picture features s 3, &785(#7, /7 Sometimes the Earth's own magnetic field may make the picture tilt. If this happens, you can correct the picture tilt. 1 Press the ë buttons to choose PICTURE TILT. Then press the 3 button The sub-menu of the PICTURE TILT function appears. 2 Press the ë buttons until the picture becomes level 3 Press the 3 button to complete the setting The menu disappears. 4< 6RXQG#VHWWLQJ s 63($. (5 You can turn off the sound from the TV speakers; but you should only do this if you have connected an audio system to the TV instead of the TV speakers. When you are using this function, see "Turning the TV's speakers off" on page 31. When there is no sound from the TV speaker: If the SPEAKER function is set to OFF, there is no sound from the TV speaker. Press the ë buttons to choose SPEAKER. [. . . ] Try to change the aerial's direction or replace it with one with better directionality. · Are your COLOUR SYSTEM settings correct?Follow the description "COLOUR SYSTEM" on page 18 to try to solve the trouble. · Have the COLOUR and BRIGHT settings been adjusted properly? [. . . ]