User manual JVC AV-28WFX1EU-AV-28WFX1

[. . . ] COLOUR TELEVISION AV-32WFX1EU AV-28WFX1EU Instructions Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. ENGLISH WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO ENSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT. Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit. Avoid damaging the AC plug and power cord. [. . . ] Note: · The DigiPure setting can be changed using the buttons on the TV's front panel. Pressing the button for 5 seconds or longer causes the current DigiPure setting to be displayed. Change the DigiPure setting while it is being displayed using the - / + buttons. 1 Press / to choose DIGITAL VNR. 2 Press / to choose AUTO. MIN: The effect of the Digital VNR function is kept at the minimum irrespective of the amount of noise in the picture. When viewing an excellent quality picture which contains almost no noise, the picture sharpness may be improved by changing the Digital VNR setting from AUTO to MIN. However, since the noise reduction effect becomes very low, this is not suitable for a picture which contains a lot of noise. MAX: The effect of the Digital VNR function is kept at the maximum irrespective of the amount of noise in the picture. When viewing a picture which contains a lot of noise, the picture noise may be further reduced by changing the Digital VNR setting from AUTO to MAX. However, since using the noise reduction at maximum may have the reverse effect of reducing the sharpness of the picture, MAX is not suitable for an excellent quality picture which contains almost no noise. 3 Press OK . This completes the setting. 16 Picture Features Colour System The colour system is automatically chosen, but if the picture is not clear or no colour appears, choose the colour system manually. 4:3 Auto Aspect You can preset one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Press / to choose COLOUR SYSTEM. Then Press . OK 1 Press / to choose 4:3 AUTO ASPECT. Then press OK . . The 4:3 AUTO ASPECT menu appears. ENGLISH 2 Press system. / to choose the appropriate colour PAL: PAL system. AUTO: Automatic colour system selection. Notes: · The AUTO may not function properly with poor signal quality. If the picture is abnormal in AUTO mode, choose another colour system manually. · When in the TV mode (PR 1 to PR 99), you cannot choose AUTO, NTSC 3. 58 or NTSC 4. 43. · When in the TV mode (PR 0), you cannot choose NTSC 3. 58 or NTSC 4. 43. 2 Press / to choose a ZOOM mode. 3 Press OK . This completes the setting. Picture Tilt There are cases where the effects of the magnetic pull from the earth may make the picture tilt . If this happens, correct the picture as follows. 1 Press / to choose PICTURE TILT. Then press OK . The PICTURE TILT menu appears. 3 Press OK . This completes the setting. 2 Press / until the picture becomes horizontal. 3 Press OK . The correction is complete. 17 Sound Setting Sound Adjustment You can adjust the sound to your liking. 1 Press / to choose an item. 2 Press / to adjust it. Item Weaker BASS TREBLE BALANCE Stronger Stronger Right 1 Display MENU. MENU OK Weaker Left 3 Press 2 Choose SOUND SETTING. P OK . This completes the settings. BBE P You can use the BBE function to enjoy easy-to- listen sound that is faithful to the original sound recorded. 3 Display the Sound Setting menu. MENU OK 1 Press / to choose BBE. 2 Press / to choose ON. To cancel the BBE function : Press / to choose OFF. Stereo / I · II You can choose Multi Sound mode for stereo broadcast programmes and bilingual programmes. 3 Press OK . This completes the setting. · Licensed by BBE Sound, Inc. BBE is a registered trademark of BBE Sound, Inc. Note: · Multi Sound has no effect on programmes other than A2 (B/G, D/K) or NICAM (B/G, D/K, L, I) broadcast programmes. Hyper Sound You can enjoy sounds with a wider ambience. 1 Press / to choose STEREO / I · II. 1 Press / Notes: · The Multi Sound mode display is different from the broadcast programme. · The Multi Sound function does not work in the EXT modes. And the STEREO / I·II does not appear in SOUND SETTING menu. to choose HYPER SOUND. 2 Press / to choose ON. · To cancel the Hyper Sound, choose OFF 3 Press OK . [. . . ] (See page 21. ) The screen turns blue. s SOUND No sound from the TV's speakers. No "SUB-I" or "SUB-II" sound in a multi-sound broadcast. The current time is not displayed. · Disconnect the headphones. [. . . ]