User manual JVC AV-32H5BU-AV-32H5 Instruction Manual

[. . . ] ENGLISH DEUTSCH FRANÇAIS NEDERLANDS CASTELLANO ITALIANO PORTUGUÊS AV-32H5SU AV-28H5SU AV-28H5SL AV-32H5BU AV-28H5BU AV-28H5BL COLOUR TELEVISION FARBFERNSEHGERÄT TELEVISEUR COULEUR KLEURENTELEVISIE TELEVISOR A COLOR TELEVISORE A COLORI TELEVISOR A CORES INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS GEBRUIKSAANWIJZING MANUAL DE INSTRUCCIONES ISTRUZIONI INSTRUÇÕES How to move the TV When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful not to trap your hands when putting the TV down. 1 ENGLISH 2 3 1 Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: · Operate only from the power source specified (AC 220 ­ 240 V, 50 Hz) on the unit. [. . . ] MIN: The level of the DIGITAL VNR effect is set to the minimum. If you set the DIGITAL VNR function to AUTO but feel that the sharpness of the original picture has not been reproduced fully, change the setting from AUTO to MIN. · The MIN setting is not suitable for lowquality pictures which contain a lot of noise. MAX: The level of the DIGITAL VNR effect is set to the maximum. If you set the DIGITAL VNR function to AUTO but still notice some noise, change the setting from AUTO to MAX. · The MAX setting is not suitable for highquality pictures which contain very little noise. OFF: The DIGITAL VNR function is turned off. 1 Choose COLOUR SYSTEM then press the a button 2 Press the 5 buttons to chose the appropriate colour system. Then press the a button PAL: PAL system SECAM: SECAM system NTSC 3. 58: NTSC 3. 58 MHz system NTSC 4. 43: NTSC 4. 43 MHz system AUTO: This function detects a colour system from the input signal. Only when you are viewing a picture from Programme number PR 0 (AV), or EXT terminal, you can choose using the AUTO function. · The AUTO function may not function properly if you have poor signal quality. If the picture is abnormal in the AUTO function, choose another colour system manually. · When in the Programme numbers PR 0 (AV) to PR 99, you cannot choose NTSC 3. 58 or NTSC 4. 43. 21 PICTURE menu 4:3 AUTO ASPECT You can choose one of three ZOOM modes, REGULAR, PANORAMIC or 14:9 ZOOM, as the ZOOM mode for the normal picture (4:3 aspect ratio). 1 Choose 4:3 AUTO ASPECT then press the a button 4:3 AUTO ASPECT PANORAMIC REGULAR 14:9 ZOOM TV OK D0017-EN 2 Press the 6 buttons to choose a ZOOM mode. Then press the a button 22 SOUND menu SOUND STEREO/ BASS TREBLE BALANCE HYPER SOUND TV OK BALANCE OFF You can adjust the volume balance between the left and right speaker. 2 : turn the left speaker's volume level up. 3 : turn the right speaker's volume level up. D0019-EN STEREO / I · II When you are viewing a bilingual broadcast programme, you can choose the sound from Bilingual I (Sub I) or Bilingual II (Sub II). When the stereo broadcasting is received poorly, you can change from stereo to mono sound so that you can hear the broadcast more clearly and easily. s: Stereo sound v : mono sound t : Bilingual I (sub I) u : Bilingual II (sub II) · The sound mode you can choose differs depending on the TV programme. · This function does not work in the EXT modes. And this function does not appear in the SOUND menu. HYPER SOUND Mono sound is converted to simulated stereo for a more enjoyable audio experience. · The HYPER SOUND function does not work properly with mono sound. · You can turn on or off the HYPER SOUND function with a single press. [. . . ] If the speakers cause this to happen, use magnetic-shielded speakers instead. · A picture may be tilted due to the influence of the earth's magnetism. In this case, use the "PICTURE TILT" on page 33 to correct the tilt. · It takes a short period of time from the time an operation such as changing channels is performed until an image is displayed. [. . . ]