User manual JVC AX-90VBK parts list

[. . . ] 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Before Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Checking the Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Connecting the Speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The stored settings for the newly selected source are automatically recalled. The following can be stored for each source: · Volume level (see page 10) · Balance (see page 12) · Loudness (see page 12) · Preset SEA modes (see page 15) · Surround mode settings (see page 17) Using the One Touch Operation To store the sound settings: 1. The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled and appear on the display in turn. Adjust the sound using the functions listed above. The newly adjusted settings are memorized. On the front From the remote control panel To recall the sound settings: With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source is recalled, and appears on the display when the source is selected. To cancel the One Touch Operation function: Press ONE TOUCH OPERATION so that the lamp goes off. (Even though the One Touch Operation function is canceled, the recalled sound effects remain active. ) ONE TOUCH OPERATION ONE TOUCH OPERATION Page 14 English One Touch Operation English Using the Preset SEA Modes The preset SEA (Sound Effect Amplifier) modes give you control over the way your music sounds. Note: The preset SEA mode cannot be used for recording. Selecting Your Favorite SEA Mode On the front panel: PRESET SEA 1. Press PRESET SEA so that the Control % / fi / @ / # buttons work for preset SEA setting. Press Control % / fi until the mode you want appears on the display. The sound is reproduced through the front speakers and rear speakers. On Dolby Surround Dolby Surround has been also developed to reproduce the important elements of the acoustic surround at home. To watch the soundtracks of video software bearing the mark DOLBY SURROUND * which includes the same encoded surround information as found in Dolby Stereo films, the amplifier can provide you with 2 Dolby Surround programs (Dolby Pro Logic and Dolby 3ch Logic). Dolby Pro Logic: Select this mode when the optional rear speakers are connected (as well as a center speaker). Dolby 3ch Logic: Select this mode when a center speaker is connected without rear speakers. * Manufactured under license from Dolby Laboratories Licensing Corporation. "Dolby, " the double-D symbol, and "Pro Logic" are trademarks of Dolby Laboratories Licensing Corporation. Notes: · The surround processor has no effect on monaural sources. · The surround processor cannot be used for recording. Using JVC's Hall Surround You need to connect one set of rear speakers to obtain the full effect. Once you have adjusted the Hall Surround, the amplifier memorizes the settings. Press SURROUND so that the Control % / fi / @ / # buttons work for selecting the surround modes. [. . . ] In this case, you must start again from the beginning. · Refer also to the manuals supplied with your CD player and cassette deck. Page 24 English COMPU LINK Remote Control System English Using the Remote Control You can operate JVC audio and video components with the amplifier's remote control, since control signals for JVC components are preset in the remote control. To operate these components with the remote control, first select a source with the source buttons on the remote control. Then, operate that source using the remote control. IMPORTANT: To operate JVC audio components using this remote control: · You need to connect JVC audio components through the COMPU LINK-3 SYNCHRO jacks (see page 7) in addition to the connections using cables with RCA pin plugs (see page 6). [. . . ]