User manual JVC AX-M9000

[. . . ] Retain this information for future reference. Serial No. LVT0377-005A [U, UB, US] Warnings, Cautions and Others Avisos, precauciones y otras notas Caution ­­ switch!Disconnect the mains plug to shut the power off completely (the STANDBY/ON lamp goes off). The switch in any position does not disconnect the mains line. [. . . ] For details, refer to chapters concerning to the particular unit. When turning off the system After pressing button, the system closes sliding panel as well as other CD tray and Tape tray automatically if they are still opened. 13 Buttons behind the sliding panel REMOTE CONTROL RM-SUXG6E PANEL OPEN/CLOSE DIMMER PANEL OPEN/CLOSE DISPLAY /CHARA. 4 ¢ SET CANCEL ENTER PLAY MODE REC MODE TITLE /EDIT CLOCK /TIMER ACTIVE BASS EX. CLOCK/TIMER SLEEP BASS TREBLE FM MODE FM MODE PLAY MODE REPEAT AUTO PRESET AUTO PRESET TITTLE/EDIT DISPLAY /CHARA. UP ENTER 4¢ SET CANCEL OPEN/CLOSE CANCEL < MD TAPE SET DOWN > AUX SET CANCEL UP/DOWN FM/AM FM/AM STANDBY/ON OPEN/CLOSE MICRO COMPONENT SYSTEM UX-G6 FM/AM CD AUX MULTI JOG MOS - FET VOLUME 4/¢ FM/AM VOLUME MULTI JOG STEREO/MONO indicator You can tune in FM and AM stations manually, automatically, and use the preset station feature. Setting the AM Tuner Interval Spacing Some countries space AM stations 9 kHz apart, and some countries use 10 kHz spacing. When shipped, the built-in AM tuner is set to 9 kHz spacing. · To set the frequency spacing -- on the front panel only Press FM/AM button first. While pressing and holding 7 (stop) button on XT-UXG6, press FM/AM button on AX-M9000 repeatedly to select "AM­9kHz" or "AM­10kHz" appeared alternately in the display window. · Each time you press the button, the band alternates between FM and AM. · If a program on FM band is broadcast in stereo, STEREO indicator lights. 2 Tuning in a Station 1 Press FM/AM button. The system automatically turns on and tunes in the last tuned station (either FM or AM). The following information appears in the display window. Select a station using one of the following three methods. · Manual Tuning Opening the sliding panel, press 4 / ¢ (lower/ higher frequencies) button repeatedly to change the frequencies step by step until you find the desired station. · Auto Tuning Opening the sliding panel, press and hold 4 / ¢ (lower/higher frequencies) button for a second or more to start searching a station and stop automatically until the station of sufficient signal strength is tuned in. Press 4 button: Goes back to the beginning of the current and previous tracks. Rotating MULTI JOG dial clockwise also changes the tracks forwards quickly, while rotating it counterclockwise the tracks reverses quickly. < / > button on the remote control is also available to skipping operations. · To stop playing back for a moment, press 6 (play/pause) button on the CD unit. The playback time starts blinking in the display window. · To resume playback, press 6 (play/pause) button again. Playback continues from the point where it was stopped for a while. 5 Press 7 (stop) button to stop playing back the CD. Following information for the CD appears in the display window. Programing the Playing Order of the Tracks -- Program Play You can arrange the order in which the tracks play before you start playback. You can program up to 32 tracks. Total track number Total playback time 1 6 Press 0 (open/close) button on the CD unit to remove the CD. · Pressing 0 (open/close) button during playback directly, the CD unit stops playback and opens CD tray. Place a CD. · If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step. Press PLAY MODE button repeatedly until "CD PROGRAM" appears in the display window. 2 Searching and Skipping Tracks While playing back a CD, you can do the following operations. · Each time you press the button, playback mode indicators also change as follows: PROGRAM RANDOM To search and skip to a particular point in a track During playback, press and hold 4 / ¢ button to meet the desired passages in a track: Press and hold or ¢ button: Fast forwards in the track. Press and hold or 4 button: Fast reverses in the track. UP/DOWN button on the remote control is also available to searching operations. Canceled (Normal play) 3 Rotate MULTI JOG dial to select a track number to be programed (< / > buttons also available). Track number Program number 17 4 Press SET button to program the track number. To erase all the programed data After playing back the CD, you can erase all the programed track data by pressing 7 (stop) button. [. . . ] The cassette deck unit cannot obtain the correct characteristics for these tapes. · Ferrochromite (FeCr) TYPE III tapes cannot be used with this cassette deck unit. 30 English English Troubleshooting If you are having a problem with your system, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the units has been physically damaged, call a qualified person, such as your dealer, for service. Symptom No sound is heard. · · · Poor radio reception. [. . . ]