User manual JVC AX-UXG6

[. . . ] COMPACT COMPONENT SYSTEM SYSTEME DE COMPOSANTS COMPACT FS-G6 STEREO AMPLIFIER Consists of AX-UXG6, XT-UXG6, TD-UXG6, and SP-UXG6. Modéles AX-UXG6, XT-UXG6, TD-UXG6 et SP-UXG6. AX-UXG6 COMPACT DISC/TUNER XT-UXG6 CASSETTE DECK TD-UXG6 SPEAKER SYSTEM SP-UXG6 POWER STANDBY/ON OPEN/CLOSE COMPACT COMPONENT SYSTEM FS-G6 FM/AM MULTI JOG AUX MOS - FET VOLUME REMOTE CONTROL RM-SFSG6J PANEL OPEN/CLOSE DIMMER POWER 1BIT P·E·M D·D·C O N V E R T E R ACTIVE BASS EX. CLOCK/TIMER SLEEP BASS TREBLE FM MODE PHONES COMPACT PLAY MODE REPEAT AUTO PRESET DIGITAL AUDIO TITTLE/EDIT DISPLAY /CHARA. UP ENTER CANCEL < MD TAPE SET DOWN > AUX FM/AM CD DOLBY B NR 4 7 ¢ + VOLUME REC PAUSE ­ AUTO REVERSE REC INSTRUCTIONS MANUEL D'INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. [. . . ] · Pressing 0 (open/close) button during playback directly, the CD unit stops playback and opens CD tray. Place a CD. · If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step. Press PLAY MODE button repeatedly until "CD PROGRAM" appears in the display window. 2 Searching and Skipping Tracks While playing back a CD, you can do the following operations. · Each time you press the button, playback mode indicators also change as follows: PROGRAM RANDOM To search and skip to a particular point in a track During playback, press and hold 4 / ¢ button to meet the desired passages in a track: Press and hold or ¢ button: Fast forwards in the track. Press and hold or 4 button: Fast reverses in the track. UP/DOWN button on the remote control is also available to searching operations. Canceled (Normal play) 3 Rotate MULTI JOG dial to select a track number to be programed (< / > buttons also available). Track number Program number 17 4 Press SET button to program the track number. To modify the program Before playing back the CD, you can erase the last programed track by pressing CANCEL button. Each time you press the button, the last programed track is erased from the end of program. · To add new tracks to the program before you start playing-back, simply select a track number again you want to add (repeat steps 3 to 4). Track number Program number Here the track number 2 on the CD is stored into a program number 1, and shortly after that the total playback time of programed tracks appears in the display window as follows: To erase all the programed data After playing back the CD, you can erase all the programed track data by pressing 7 (stop) button. New program can be entered again. To exit from the Program play mode Total playback time 5 Repeat steps 3 to 4 to program other tracks you want up to 32 tracks. · If you try to program a 33rd step "MEMORY FULL" will appear in the display window, and your entry is ignored. · The total playback time of programed tracks exceeds 99'59" "­ ­ : ­ ­" will appear in the display window. Before or during playback, you can exit from Program play mode as follows: · Before playback, press PLAY MODE button twice. · During playback, press 7 (stop) button then PLAY MODE button twice. Playback mode indicator goes off and the system resumes Normal play mode. Pressing 0 (open/close) button to open the CD tray also quits and erases the program play. 6 Press 6 (play/pause) button on the CD unit. The programed tracks are played back in the order you have set. · Other CD operations are the same as Normal play. Press 7 (stop) button to quit the Program play. · When Program play finished, CD unit automatically stops. 7 To check the program contents Before playing back the CD, you can check the program contents by using 4 / ¢ button. Press ¢ button: Shows the programed tracks in the programed order. Press 4 button: Shows them in the reverse order. 18 English Continued English Continued Playing at Random -- Random Play The tracks of the loaded CD will play in no special order (at random) when you select this mode. Repeating Tracks -- Repeat Play You can have the entire disc, the programed tracks, or the individual track repeat as many times as you like. 1 Place a CD. If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step. Press PLAY MODE button repeatedly until "CD RANDOM" appears in the display window. 1 Place a CD. If the current playing source is not the CD, press 6 (play/pause) button on the CD unit, then 7 (stop) button before going to the next step. Press REPEAT button on the remote control repeatedly to set the repeat mode. · Each time you press the button, repeat mode indicators light in the display window, and Repeat playback mode changes as follows: 2 2 · Each time you press the button, playback mode indicator also changes as follows: PROGRAM RANDOM Canceled (Normal play) Canceled (Normal play) : 3 Press 6 (play/pause) button on the CD unit. Repeats one track on the CD or in a program. [. . . ] WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800)537-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department. [. . . ]