User manual JVC BR-DV6000U-BR-DV6000 Instruction Manual

[. . . ] U E CAUTION This section of instruction manual is specially edited for service purpose with modified contents. It is not recommended to use this section for the substitution of the original book in the merchandise. CAUTION This section of instruction manual is specially edited for service purpose with modified contents. It is not recommended to use this section for the substitution of the original book in the merchandise. DV VIDEO CASSETTE RECORDER DV VIDEO CASSETTE RECORDER BR-DV6000U INSTRUCTION MANUAL BR-DV6000E INSTRUCTION MANUAL OPERATE OPERATE Mini MENU DISP RESET A. DUB PROFESSIONAL REC PLAY PAUSE Mini MENU DISP RESET A. DUB PROFESSIONAL REC PLAY PAUSE INDEX­ MIC SET INDEX+ EJECT REW STOP FF INDEX­ MIC SET INDEX+ EJECT REW STOP FF HOLD BLANK CUE UP HOLD BLANK CUE UP PHONES REC LEVEL CH-1/3 CH-2/4 BR-DV6000 AUDIO INPUT COUNTER MONITOR OUTPUT SELECT REMOTE CTL L CH-1/2 DV TC MIX MIX LINE R CH-3/4 Y/C UB LOCAL (CPN) PHONES REC LEVEL CH-1/3 CH-2/4 BR-DV6000 AUDIO INPUT COUNTER MONITOR OUTPUT SELECT CH-1/2 DV CTL L TC MIX MIX LINE R CH-3/4 Y/C UB (CPN) REMOTE LOCAL This instruction book is made from 100% recycled paper. Thank you for purchasing this JVC product. [. . . ] Set the [REMOTE/LOCAL] switch on the front panel to "REMOTE". Set BACKUP REC TIME in the SYSTEM (1/2) Menu screen. Use the following settings according to the tape length of the source unit. * For DV or mini DV cassette tape: 25MIN : 30-minute tape 55MIN : 60-minute tape 75MIN : 80-minute tape 115MIN : 120-minute tape 175MIN : 180-minute tape 265MIN : 270-minute tape OFF : No backup recording :Operation: :Connection: · Serial remote controller: RM-G30 · Foot switch 1. Recording begins on the source unit. Ensure that recording starts from the beginning of the recording tape. 2. BR-DV6000 begins recording when the tape of the source unit nears its end (about 5 minutes before the end of the tape). · BR-DV6000 begins recording when the recording time of the source unit reaches the time set by BACKUP REC TIME. The serial remote controller (RM-G30, sold separately) can be connected to the SERIAL REMOTE IN terminal located on the rear panel of BR-DV6000. The input signals of the SERIAL REMOTE IN terminal can be throughoutput from the SERIAL REMOTE OUT terminal. (Only with OPERATE ON) :Setting: Memo Besides recording, the serial remote controller can perform other functions. If the REMOTE SEL SER is set to ON, unit buttons that can be operated can be selected from LOCAL FUNCTION in the REMOTE (1/2) Menu screen. REMOTE (2/2) Menu screen ------R E M O T E [ 2 / 2 ] ------ R EM F F / R EW MOD E F F / R EW REM S TOP SE L . EE PB START DELAY OF SYNCHRON I Z A T I ON ON CON T ROL L ER SE L TYPE1 F OO T SW OFF PAGE BACK Memo · In backup recording, BR-DV6000 records video/sound from the source unit. While this unit is performing backup recording, continue shooting from the source unit. · The audio mode is the one selected in the source unit. (32 K/48 K) · Set BACKUP REC TIME to "OFF" if the unit is not performing backup recording. To use the SERIAL IN terminal, set REMOTE SEL SER in the REMOTE (1/2) Menu screen to ON or LOC+REM. Then, set the REMOTE/LOCAL switch on the front panel accordingly. REMOTE SEL SER ON : When the REMOTE/LOCAL switch is set to REMOTE, operations can be performed via the SERIAL REMOTE IN terminal. LOC+REM: With the REMOTE/LOCAL switch is set either way, operations can be performed via the SERIAL REMOTE IN terminal. With this setting, the buttons and switches of the unit can be used too. Memo With REPLICATION in the SYSTEM (2/2) menu screen set to "DV", BACKUP REC TIME is fixed to "OFF". For using the backup recording function, set REPLICATION to "OFF" or "SERIAL". Set FOOT SW in the REMOTE (2/2) Menu screen according to how the serial remote terminal is used. OFF : Set to OFF when the serial remote controller is used. L EDGE : Recording and recording pause is switched at the LOW edge of the footswitch signal. H EDGE : Recording and recording pause is switched at the HIGH edge of the footswitch signal. L LEVEL : Recording is performed at the LOW edge and paused at the HIGH edge of the footswitch signal. Set the REMOTE SEL DV in the REMOTE (1/2) Menu screen to ON or LOC+REM. Set TC DUPLICATE in the TC/UB/ CLOCK (1/2) Menu screen to OFF. · It records the data of the built-in time code generator. · When TC DUPLICATE is set to AUTO, the time code of the DV camcorder will stop advancing. [. . . ] Remove the RS-422A REMOTE 1 terminal. 1 terminal. 1 Remove the two screws Å and pull out the RS-422A REMOTE the RS-422A REMOTE board. Remove the cable carefully not to damage it. 2 Remove the connector cable connected to the connector of REMO RS-422A REMOTE 2. Remove the plate of RS-422A REMOTE 1 terminal. Plate Hexagon screw Socket wrench SA-K46U · For removing the plate, remove the two hexagonal screws first with a tool such as a socket wrench. Video Recording format : 8 bit, 13. 5 MHz, 4:1:1 (NTSC) 4:2:0 (PAL) : 1. 0V (p-p), 75 Ø unbalanced : 1. 0V (p-p), 75 Ø unbalanced : 0. 286V (p-p), 75 Ø unbalanced : 1. 0 V (p-p), 75 Ø unbalanced (100%, Color Bar) : 0. 7 V (p-p), 75 Ø unbalanced (75%, Color Bar, Setup 7. 5%) : 0. 7 V (p-p), 75 Ø unbalanced (75%, Color Bar, Setup 7. 5%) : 1. 0V (p-p), 75 Ø unbalanced : 1. 0V (p-p), 75 Ø unbalanced : 0. 286V (p-p) (NTSC) / 0. 3V (p-p) (PAL) 75 Ø unbalance 3. Remove the SA-K46U plate in the same procedure above. [. . . ]