User manual JVC CA-HXZ30 INSTRUCTION MANUAL

[. . . ] COMPACT COMPONENT SYSTEM Espaol For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. SISTEMAS DE COMPONENTES COMPACTOS SISTEMA DE COMPONENTE COMPACTO INSTRUCTIONS MANUAL DE INSTRUCCIONES INSTRUES GVT0100-012A [UW, UJ] Portugus CA-HXZ30 CA-HXZ10 English Warnings, Cautions and Others Avisos, precauciones y otras notas Advertncias, precaues e outras notas Caution (standby/on) button! [. . . ] For track number 32, press +10 three times, then 2. For track number 132, press +10 thirteen times, then 2. FM MODE 16 English TUNING TUNING English Programming the Playing Order of the Tracks --Program Play You can arrange the playing order of the tracks before you start playing. To use Repeat Play (see page 19) for Program Play, press REPEAT after starting Program Play. Only REPEAT 1 and REPEAT ALL can be selected for Program Play. There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 2 again. 4 Select a track from the selected disc in step 3. Program step numbers exceeding 100 cannot be programed. When making programs from MP3 discs, the unit only recognizes tracks like audio CD. You cannot make programs using group numbers. On the unit: 1 2 Load discs. If the current playing source is not the CD player, press CD 38, then 7 before going to the next step. Turn / 4 to select the track number, then press SET/DISPLAY. On the remote control: PRESET SET /DISPLAY TUNING Activate Program Play. On the unit: Press the number buttons. CD PLAY MODE Press CD PLAY MODE repeatedly until "CD PROGRAM" appears on the display. Each time you press the button, the play mode changes as follows: CD PROGRAM CD RANDOM For how to use the number buttons, see "To go to another track directly using the number buttons" on page 16. FM MODE 5 Program other tracks you want. To program tracks from the same disc, repeat step 4. To program tracks from a different disc, repeat steps 3 and 4. Total track number and total playing time (Continuous Play) On the remote control: Press PROGRAM so that "CD PROGRAM" appears on the display. 6 5 PROGRAM PROGRAM CANCEL REC DOM START/STOP Press CD 38. CD TAPE The PROGRAM indicator lights up on the display. The tracks are played in the order you have programed. If the playing disc is an MP3 disc, the MP3 indicator lights up. To stop playing, press 7. If a program has been stored in memory, the program is called up. To exit from Program Play, press CD PLAY MODE repeatedly until the PROGRAM indicator goes off (or press PROGRAM on the remote control) after playback stops. 3 Press one of the disc number buttons (CD1 CD5) to select the disc you want. CD1 CD2 CD3 CD4 CD5 Track number Program step number Disc number If you try to program a 101st track, "CD FULL" appears on the display. If you have tried to program a track from an empty tray, "NO READ # (number)" or "NO DISC # (number)" will appear on the display for 2 seconds. If you have tried to program a track number that does not exist, it is ignored. If you try to open a disc tray during Program Play, the disc tray does not come out. Open disc trays after canceling Program Play. 17 Continued To check the program contents On the remote control ONLY: Before playing, you can check the program contents by pressing () or 4 (1). () : Shows them in the programed order. 4 (1) : Shows the programed tracks in the reverse order. Playing at Random--Random Play The tracks of all the loaded discs will be played at random. To use Repeat Play (see page 19) for Random Play, press REPEAT after starting Random Play. Only REPEAT 1 and REPEAT ALL can be selected for Random Play. 1 2 Load a disc. Press the corresponding disc number button (CD1 CD5) where a disc is loaded in step 1, then press 7. CD1 CD2 CD3 CD4 CD5 To modify the program To erase the last programed tracks, press CANCEL/DEMO (or press PROGRAM CANCEL on the remote control). Each time you press the button, the last programed track is erased from the program. CANCEL /DEMO CD 3 CD TUNING /BEEP PROGRAM PROGRAM CANCEL REC M START/STOP TAPE 3 To add tracks into the program before playing, simply select the track numbers you want to add by following step 4 of the programming procedure. If you want to add tracks from another disc, follow steps 3 and 4. [. . . ] 6) Ruido de conmutacin provocados por la operacin de los selectores del amplificador. 7) Continua oscllacin de alta fracuencia o de sonidos de tonos altos provocados por instrumentos electrnicos. PRECAUCIN No arrastre ni empuje los altavoces sobre el piso o la mesa. De lo contrario, las cuatro patas del lado inferior de cada altavoz se podran desprender o salir del altavoz. LIGAO NO use outro amplificador para operar este sistema de altifalantes excepo do CA-HXZ10. [. . . ]