User manual JVC CA-MXKA6

[. . . ] COMPACT COMPONENT SYSTEM CA-MXKA3 STANDBY/ON SLEEP AUX FM MODE FM /AM CD1 CD2 CD3 CD REPEAT PROGRAM /RANDOM TAPE A/B TAPE SELECT RDS MODE DISPLAY MODE SOUND MODE VOLUME ACTIVE BASS EX. SOUND TURBO FADE MUTING RM-SMXKA6R REMOTE CONTROL INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT1013-003A [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] (DISC1 is selected) Shows that this disc number is selected. When you use an 8 cm (3'') CD, place it on the inner circle of the tray. You can load CDs while listening to the other source or while listening to the CD being played back. When power is turned off with the tray opened, the tray is automatically closed. If the CD cannot be read correctly (because it is scratched, for example), " 0 0:00" appears on the display. Shows that the disc is rotating. To Unload CDs Take out the CD as shown below. One Touch Play The power comes on, and operations are done automatically. By pressing the CD 6 button, the System will come on, and if a CD is loaded for the disc number that was lastly selected, it will start playing from the first track. By pressing the CD1-CD3 button, the System will come on, and if a CD is already loaded for the selected disc number, it will start play from the first track. 1 2 3 4 While the CD Player is stopped, press the CD Open/Close 0 button on the Unit to open the tray. Remove the CD, then press the DISC SKIP button on the Unit. The tray turns for the next CD. Repeat step 2 to remove all the CDs. Press the CD Open/Close Unit to close the tray. To Load CDs 1 2 Press the CD Open/Close Unit to open the tray. 0 button on the 0 button on the You can remove CDs while listening to the other source. Place a CD, with its label side up, onto the tray. Be sure that the CD is securely seated on the disc tray. With the label side up You can also remove the CDs during playback. However, in this case, you can only remove the CDs that are not being played back. CD-R / RW PLAYBACK 3 4 5 Press the DISC SKIP button on the Unit and place the next CD. When you press the button, the tray turns for the next CD. Repeat step 3 for the last CD. Press the CD Open/Close Unit. The tray is closed. 0 button on the When placing a disc in the tray, be sure to position the disc inside the recess correctly. Otherwise, the message "NO DISC" will appear in the display, and the disc may be damaged or the unit may be damaged when the tray is opened, or it may be difficult to remove the disc from the unit. 15 Using the CD Player Basics of Using the CD PlayerNormal Play To Play CDs Removing/changing the CDs during playback While playing back a CD (e. g. CD1), you can remove or change the other CDs (e. g. CD2 and CD3) by pressing the CD Open/Close 0 button. After removing or changing, press the same button to close the tray. To Select a Track During playback (using the 4 or button): Briefly press the 4 or button to select the track you want to play. By pressing the button, you can skip to the next track or skip back to the previous track. Press the button once to skip to the beginning of the next track. CD1 = CD2 = CD3). ) Press the 4 button to skip to the beginning of the current track. Press twice quickly to skip to the beginning of the previous track. (You cannot skip back to the previous CD. ) In Stop mode (using the 4 or button): By briefly pressing the 4 or button, the CD Player operates in the same way as during playback, except the following point. The buttons are effective only for the currently selected CD. Using the numeric keys on the Remote Control: Using the numeric keys, you can directly select the track on the currently selected CD. For example, press +10, then 5 to play back the track number 15. [. . . ] Should this occur, the System may malfunction. In this case, leave the System turned on for a few hours until the moisture evaporates, unplug the AC power cord, and then plug it in again. 28 Troubleshooting If you are having a problem with your System, check this list for a possible solution before calling for service. If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as your dealer, for service. Possible Cause Connections are incorrect, or loose. [. . . ]