User manual JVC CA-MXS6

[. . . ] COMPACT COMPONENT MD SYSTEM CA-MXS6MDR STANDBY /ON LEVEL METER DIMMER COMPACT COMPONENT MD SYSTEM MX-S6MDR MENU DISC SP/LP2/LP4 LONG MODE REC MODE LINE REC PAUSE RM-SMXS6MDR REMOTE CONTROL HIGH SPEED CD MD DISC LOADING MECHANISM TITLE/EDIT ENTER /DEMO PHONES LINE 2 COMPACT DIGITAL AUDIO INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0528-001A [B] Warnings, Cautions and Others IMPORTANT for the U. K. [. . . ] · Sound quality will decrease as the recording length mode changes to LP2 (little) and LP4 (much). To obtain the best sound quality, it is recommended to use the SP mode when recording. ­ 35 ­ Continued About High-Speed Recording There are some restrictions to observe for high-speed recording (exceeding normal speed) to protect copyrights. (HCMS: see page 69. ) This unit is so designed that a song (track) recorded from a CD using high-speed recording cannot be rerecorded until 74 minutes elapse after the previous recording started. If you try to re-record the same song (track) within the 74 minutes, recording is canceled and the display turns red with "HCMS CANNOT COPY" shown as a warning. Recording Any Sound Source -- Standard Recording The following recording method can be applied to any sound source. 1 Insert a recordable MD in the MD loading slot. 2 Select the source. · When recording CDs: On the unit: Press DISC to select a disc, and press CD # / 8, then press 7. On the remote control: Press CD1, CD2, or CD3 to select a disc you want to record with, then 7. · When recording an FM/AM (MW/LW) broadcast: Press FM/AM, then tune into a station you want. · When recording from external equipment: Press LINE repeatedly until the external equipment you want is selected. When the source for recording is the equipment connected to either the LINE 1 jacks or the LINE 2 jack, you can select the sound input level. See "Selecting the sound input level" on page 65. The remaining time required until re-recording will then appear in the main display. If this happens, press 7 after the remaining time appears. REMEMBER if you are trying to record a program including the same song (track) twice using high-speed recording, recording will stop at the beginning of the 2nd recording of the same song (track). ("HCMS CANNOT COPY" will appear in the main display. ) During high-speed recording You cannot listen to any source, and therefore, cannot adjust the volume level. ("CANNOT LISTEN!" will appear if you try to do. ) 3 Press LONG MODE on the unit if necessary. The recording length mode changes as follows: SP (Standard Play) LP2 (2 Times Long Play) LP4 (4 Times Long Play) · For the recording length mode, see "Stereo LongHour Recording (MDLP)" on page 35. 4 Press REC PAUSE on the unit (or MD REC PAUSE on the remote control). The REC PAUSE lamp on the unit starts flashing. 5 Press MD # / 8. The REC PAUSE lamp stops flashing and remains lit, and recording starts. · When recording an FM/AM (MW/LW) broadcast: The station frequency will be recorded as the track title. ­ 36 ­ 6 When recording a CD: Press CD # / 8. When recording from external equipment: Start playback. · For details, see the manual supplied with your equipment. To stop recording for a moment, press REC PAUSE (or MD REC PAUSE) again. To resume recording, press MD # / 8 again. (A track mark is recorded when you resume recording. ) To stop recording, press 7. "WRITING" flashes for a while. · When recording from a CD, both the CD player and the MD recorder stop. When recording from a CD using Standard Recording Two track marks may be recorded at the beginning of the recording. [. . . ] · Ausführlichere Informationen über die Displaydemonstration finden Sie auf Seite 9. Demostración en pantalla Cada vez que usted enchufa el cable de alimentación de CA en un tomacorriente de CA, se iniciará automáticamente la demostración en la pantalla principal. Para detener y cancelar la demostración en pantalla, pulse ENTER/DEMO en la unidad para que se visualice "DEMO OFF!" en la pantalla principal. · Para una información más detallada sobre la demostración, consulte la página 9. Français Italiano Démonstration des affichages Chaque fois que vous branchez le cordon d'alimentation dans une prise secteur, la démonstration des affichages démarre automatiquement sur l'affichage principal. Pour arrêter et annuler la démonstration des affichages, appuyez sur ENTER/DEMO sur l'appareil de façon que "DEMO OFF!" apparaisse sur l'affichage principal. [. . . ]