User manual JVC CA-XLEX90

[. . . ] COMPACT COMPONENT SYSTEM CA-EX90 RX-EX90 Consists of RX-EX90, ME-EX90 and XL-EX90. INTEGRATED AMPLIFIER/TUNER SUBWOOFER AMPLIFIER ME-EX90 COMPACT DISC PLAYER XL-EX90 RX-EX90 INTEGRATED AMPLIFIER / TUNER VOLUME BAND S. BASS PHONES DIRECT INPUT DOWN UP STANDBY KEY MODE POWER RX-EX90 6 dB ME-EX90 RM­SEEX90U REMOTE CONTROL SUBWOOFER AMPLIFIER 2 dB 4 dB 8 dB SUBWOOFER VOLUME 10 dB POWER 1 2 3 SLEEP 0 dB 12 dB 4 5 6 AUX 7 8 9 FM MODE /MUTING TUNER STANDBY 10 PLAY MODE +10 SUBWOOFER LEVEL POWER REPEAT CD CD 1 CD 2 CD 3 TAPE DIRECT S. A. BASS ME-EX90 TREBLE BALANCE BA SS ­/L CL O /TIM CK ER +/ R CA NC EL XL-EX90 SE T COMPACT DISC PLAYER /CANCEL L PERO TANT O C IR TA EC P E TIO N CD 3 PLAY & EXCHANGE D CD 2 CD 1 VOLUME STANDBY REPEAT PLAY MODE M FA UD TIN E G EC E R US PA POWER XL-EX90 INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. [. . . ] This switches the reception mode to auto tuning. When a program is broadcast in stereo the STEREO indicator lights up and you hear the stereo sound. When in monaural, the STEREO indicator goes off and you hear monaural sound. Normally, it is recommended to use Automatic tuning. If clear reception is not possible with the supplied antenna, connect an external antenna (see page 14). 25 CA-EX90 Presetting Stations Once stations are preset, they can be called up quickly with preset tuning. You can preset a total of 40 stations, either FM or AM. 1 Tune in the station you want to preset. Use the buttons on the remote control to tune in the station; otherwise, following operation will not be possible. T SE 2 Press SET. The unit switches to preset memory mode ("-- --" and PRESET blink in the display). Proceed to step 3 during the 4 seconds that "-- --" and PRESET are blinking. After 4 seconds, preset memory mode is released. If this happens, press SET again to reactivate it. 1 4 7 10 2 5 8 +10 3 6 9 3 Use the number buttons on the remote control to specify the preset number you desire. The preset number and PRESET blink in the display. Proceed to step 4 during the 4 seconds that the preset number and PRESET are blinking. After 4 seconds, preset memory mode is released. If this happens, start again from step 2. 4 Press SET again. SE T "MEMORY" is displayed and the station is stored at the selected preset number. If another station was previously stored at that preset number, that station is erased and the new station is memorized in its place. 26 CA-EX90 Listening to Preset Stations This section explains how to tune in preset stations. From the front panel KEY MODE 1 Press KEY MODE so that "PRESET" appears in the display. 2 Press > (for higher numbers) or < (for lower numbers) repeatedly to select the preset you desire. From the remote control You can tune in the preset stations from the remote control either, by switching through the presets one by one, or by specifying the preset you desire. TUNER 1 Press TUNER to select the tuner operations. In addition to selecting the FM band, this operation also sets the remote control to tuner operation mode. The remote control must be set to the tuner operation mode before proceeding to the following steps, even if the band was previously set to FM using the controls on the front panel. 2 Select the preset station you desire. To switch through the preset stations one by one Press > (¢ ¡) (for higher numbers) or < (4 1) (for lower numbers) repeatedly to select the preset number you desire. To specify the preset stations Use the number buttons to select a preset number. · For preset number 15, press +10 then 5. · For preset number 20, press +10 then 10. · For preset number 30, press +10, +10, then 10. 27 CA-EX90 CD Operations Loading CDs The CD player's unique 3 disc changer mechanism houses 3 individual disc trays inside the main tray. CD 3 CD 2 CD 1 1 Press 0 (open) for the disc tray (CD 1to 3) you want to load. The main tray opens to the selected disc tray. The disc tray number and "OPEN" appear in the display. Example) When CD1 0 is pressed · The disc trays housed in the main tray are numbered CD 1, CD 2, and CD 3 starting from the bottom tray. One touch operation When the unit is in the STANDBY mode, press one 0 to automatically turn the power on and open to the selected tray. 2 Place a CD with the label side facing up. Place CD singles (8 cm) in the depressed inner circle. 3 Press the same 0 you pressed in step 1. The main tray closes. The disc tray number and "CLOSE" appear in the display. Example) When CD 1 0 is pressed · Repeat steps 1 to 3 to load up to 3 CDs. Displayed information When a CD is loaded, the disc number for that CD is displayed and the player reads the disc's data. After the data is read, the display shows the total number of tracks and total playing time of the disc, then switches to show the playing time for the first track. DISC DISC Reading data Total number of tracks and total playing time (shown for 4 seconds) Playing time for track 1 DISC Likewise, when playback is stopped, the display shows the total number of tracks and total playing time of the current disc for 4 seconds, then it shows the playing time for track 1. Tip When loading more than one CD, instead of closing the main tray, press 0 for the next tray you want to load, the main tray automatically closes and then reopens to selected disc tray. CAUTION The disc tray will close if pushed inward. [. . . ] WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800)537-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department. [. . . ]