User manual JVC DLA-HX2U-DLA-HX2 INSTRUCTION MANUAL

[. . . ] ® ® PROJECTOR INSTRUCTIONS DLA-HX2U/DLA-HX2E PC VIDEO OPERATE W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. MENU EXIT ENTER PRESET HIDE For customer Use: Enter below the Serial No. which is located on the side panel of the cabinet. Retain this information for future reference. DLA-HX2U Serial No. SAFETY PRECAUTIONS IMPORTANT INFORMATION NOTICE (For USA) Language for Manuals of Products using HID Lamps (that contains mercury) This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. [. . . ] Adjusting the Zoom Ring (the screen size) To enlarge the screen size: Turn the zoom ring towards the `Wide side' To reduce the screen size: Turn the zoom ring towards `Tele side' 4. `Far side' 4. Adjusting the Focus Ring (Focus) To focus on nearer points: Turn the focus ring towards the `Near side' To focus on farther points: Turn the focus ring towards the `Far side' 26 Basic Operations 5. Adjusting the Sound Volume To increase the volume : press [VOLUME] ª (0 50) To lower the volume : press [VOLUME] · (50 0) VOL. VOLUME STAND BY LAMP TEMP OPERATE Projector: Control panel Remote control unit When "Menu display" ( page 39) is set to "15sec", after pressing the [VOLUME] button, the sound volume display will appear on the screen for about 15 seconds. (Press [EXIT] button to immediately remove the "Audio-Vol" display. ) PC VIDEO 6-1 VOL. V-KEYSTONE H-KEYSTONE 5 Audio-Vol 12 MENU EXIT ENTER Audio-Vol 12 Screen display Note · When the sound volume is displayed on the screen, pressing the [PRESET] button will reset the set value to "0". OPERATE PC VIDEO 6-1 6. Power Off 1 Press the [OPERATE] button on the projector (or the [OPERATE] button on the remote control unit ) for 1 second or more · The [OPERATE] indicator will disappear, the [STAND BY] indicator starts to blink, and the projector goes into the cooldown mode. The [STAND BY] indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode). W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. 5 MENU EXIT ENTER Turn off PRESET HIDE Blink OPERATE OPERATE STAND BY LAMP TEMP OPERATE Projector: Control panel Remote control unit Projector: Indicator Note · The [OPERATE] button will not work for approximately 1 minute from when the light-source lamp is turned on. Wait approximately 1 minute before pressing. 2 Plug out the power cord from wall outlet Caution · Please do not pull out the plug from the power source when the [STAND BY] indicator is blinking. It will shorten the life of the lamp and cause a malfunction. 27 Basic Operations Frequently used Convenient Functions PC VIDEO OPERATE When an image is projected onto the screen, the following operations can be performed directly without going through the menu operation. ( page 27 for VOLUME operation. ) W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE VOLUME FOCUS QUICK ALIGN. MENU EXIT DIGITAL ZOOM HIDE FREEZE KEYSTONE QUICK ALIGN. (quick alignment) ENTER Enlarging the Image HIDE PRESET We can zoom in while not changing the size of the projected image. After zooming, the position of the image displayed can be moved. · This cannot be done using the projector buttons. Please use the remote control unit. 1. Press [DIGITAL ZOOM] ª "Digital zoom" Display · The "Digital zoom" display appears on the screen and the projector changes to the Digital Zoom Mode. · The image on the screen can be enlarged in 8 stages by pressing this button (including the standard size). Direction buttons available Digital zoom X1. 2 DIGITAL ZOOM Direction buttons available Digital zoom X1. 2 "x2. 0" Direction buttons available Digital zoom X2. 0 1 Magnifying power display "x1. 0": 1 time (standard) "x1. 2": 1. 2 times "x1. 4": 1. 4 times "x1. 6": 1. 6 times "x2. 0": 2 times "x2. 5": 2. 5 times "x3. 2": 3. 2 times "x4. 0": 4 times Remote control unit 2. While "Digital zoom" display appears on the screen, you can move the zoomed image with the cursor buttons on the remote control To see the upper part of zoomed image: Press To see the lower part of zoomed image: Press To see the right part of zoomed image: Press To see the left part of zoomed image: Press 2 Level Display Level shown is based on selected magnification. ENTER Note · The quality of the zoomed image is reduced in comparison with the original. Remote control unit Direction buttons available Digital zoom X2. 0 Direction buttons available Digital zoom X2. 0 To reduce the size of the image When the [DIGITAL ZOOM] · button is pressed, the previously enlarged image will be reduced progressively until it returns to the original size. DIGITAL ZOOM To reduce the image to the original size When the [PRESET] button is pressed, the image will return to its original size and position. (Please operate while "Digital zoom" is displayed. ) PRESET 28 Basic Operations Turning Off Image and Sound Video images and audio output can be turned off temporarily. Press the [HIDE] button once · Images and audio output turned off. HIDE HIDE MENU EXIT Projector: Control panel ENTER Remote control unit Press the [HIDE] button again. Images and audio output turn on again PRESET HIDE Note · When the projected image input is changed, the HIDE function is cancelled and image and sound return. PC VIDEO OPERATE Displaying a Still Picture W V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM S FREEZE The projected image can be paused temporarily. · This operation cannot be operated by the projector buttons. Please use the remote control unit. VOLUME FOCUS QUICK ALIGN. Press the [FREEZE] button MENU EXIT ENTER · The image pauses after the [FREEZE] button is pressed for a few seconds and a message "Frozen" is shown in the center of the screen. An icon indicating [FREEZE] mode will be displayed on the top right corner of the screen. FREEZE Frozen PRESET HIDE Digital zoom available Remote control unit FREEZE [FREEZE] icon To de-freeze the image When you press the [FREEZE] button again, the image de-freezes and resumes. Notes · After de-freezing a still image, note that the projector will not play the image that comes immediately after. (Should you want to play the image that comes immediately after that at which the [FREEZE] button was pressed, please pause the image using the controls at the input device. ) · [MENU], [QUICK ALIGN. ], [H-KEYSTONE] and [V-KEYSTONE] buttons do not function when the image is still. [. . . ] · This product conforms to the `Household electric appliances and general-purpose articles harmonics control measure guideline'. 56 Specifications Dimensions (unit: mm) Top Bottom 181 20 360 300 8. 2 M6 (Depth 10 mm) 92. 5 67. 5 Center of lens 298 2 7 Attachment screw should be more than 6 mm but less than 10 mm in length. Front 89 Side 115. 9 65. 4 267 25 - 56 15 109 36. 2 292 38. 2 298 57 Specifications Pin arrangement Y/C terminal 4 2 3 1 Pin number 1 2 3 4 Signal name GND (Y) GND (C) Y C RS-232C IN/OUT terminal 9876 Pin number 1 2 3 Signal name N/C RD TD N/C GND Pin number 6 7 8 9 Signal name N/C N/C N/C N/C N/C 54321 4 5 PC 1 terminal 11 12 13 14 15 Pin number 1 2 3 4 Signal name Red Green Blue N/C N/C GND (Red) GND (Green) GND (Blue) Pin number 9 10 11 12 13 14 15 Signal name N/C GND (SYNC) GND N/C H. SYNC V. SYNC N/C 6 7 1 2 8 3 4 5 9 10 5 6 7 8 PC 3 terminal Pin number 8 7 65 4 3 2 1 16 15 14 13 12 11 10 9 24 23 22 21 20 19 18 17 Signal name TMDS data 2 TMDS data 2 + TMDS data 2/4 shield N/C N/C DDC clock DDC data N/C TMDS data 1 TMDS data 1 + TMDS data 1/3 shield N/C Pin number 13 14 15 16 17 18 19 20 21 22 23 24 Signal name N/C TMDS +5 V power supply Earth (+5 V) Hot plug detection TMDS data 0 TMDS data 0 + TMDS data 0/5 shield N/C N/C TMDS clock shield TMDS clock + TMDS clock - 1 2 3 4 5 6 7 8 9 10 11 12 TMDS = Transition Minimized Differential Signaling DDC = Display Data Channel 58 Specifications RS-232C external control By connecting a computer to the projector with a RS-232C cross cable (D-sub 9 pins), you can control the projector with the computer. The commands to control the projector and the response data format against the received commands are explained here. For details, please consult the authorized dealer where you purchased your projector. 1. Communication Specifications The communication specifications are as follows. [. . . ]