User manual JVC DR-MV2SEU

[. . . ] DVD VIDEO RECORDER & VIDEO CASSETTE RECORDER DR-MV2SEU OPEN/ CLOSE ON SCREEN SET UP EJECT STANDBY/ON VCR . @/: ABC DEF DVD REPEAT GHI JKL MNO ZOOM PQRS TUV W X YZ PR CLEAR AUDIO PROG TIMER SHOWVIEW TOP MENU MENU/LIST ENTER RETURN R SLOW PL AY SLOW DVD REC STOP PAUSE VCR SLOW VCR VCR REC DUBBING SEARCH REC SPEED REC VCR MONITOR SYSTEM STANDBY/ON DUBBING VCR PR VCR VCR/DVD DVD DVD S-VIDEO VIDEO (MONO) L-AUDIO-R R RM-SDR057E INSTRUCTIONS SHOWVIEW is a registered trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Development Corporation. ???????-????LPT1076-014A EN Before You Start Accessories Supplied · Remote control with two R6 (AA) batteries · Instruction Manual · RF cable · Scart cable Before You Start IMPORTANT Please read the various precautions on pages 2 to 4 before installing or operating the unit. Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The rating plate and the safety caution are on the rear and the bottom of the unit. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] (Refer to "Recording Speed" on page 23 for DVD or page 64 for VCR. ) For disc: Press [DVD REC I] on the unit to start recording. For tape: Press [VCR REC I] on the unit to start recording. VCR to DVD 5 Select "VCRDVD" using [Cursor U / D], then press [ENTER]. Dubbing Mode VCR DVD DVD VCR VCR DVD 6 7 Press the PLAY button on the external recording component. For disc: Press [DVD STOPS] on the unit to stop recording. For tape: Press [VCR STOP/EJECT S/O] on the unit to stop recording. 6 7 8 Press [SET UP] to exit the setting menu. Press [DVD]. Make sure to select a recording speed using [REC SPEED]. (See page 23. ) Note · During recording, if a signal other than PAL is detected (such as NTSC), recording is paused. Press [VCR]. 34 EN 9 Press [VCR PLAY P] on the unit, and then press [PAUSE p] at the point you wish to start recording. VCR to DVD duplication will start. 11 Press [STOP S] to stop the recording. Note · When you turn off the unit after setting the Dubbing Mode to DVDVCR, the setting will be set to VCRDVD automatically. · Dubbing Mode is available only if the tape or disc is not copy protected. · You cannot change the output mode during VCR to DVD or DVD to VCR duplication. 10 Press [DUBBING]. 11 Press [STOP S] to stop the recording. Note For VCR to DVD duplication: · After starting VCR to DVD duplication, the picture may be distorted because of the auto tracking function. Be advised to play back the tape until the picture is stabilized, then set the starting point which you wish to start recording, and start VCR to DVD duplication. · If the playback sound mode of VCR is set to "STEREO, " "LEFT" or "RIGHT, " the sound mode upon dubbing is automatically switched to "STEREO. " If the playback sound mode is set to "MONO, " the sound mode upon dubbing is also "MONO. " · If you set "External input Audio" to "Stereo, " the sound is recorded in "Stereo" (both Video mode and VR mode. ) · While in video mode, if you set "External input Audio" to "Bilingual, " "Bilingual Recording Audio" mode is recorded. While in VR mode, if you set "External input Audio" to "Bilingual, " bilingual audio is recorded. · The main and sub audio will be simultaneously recorded (VR mode. ) You can select audio modes during playback. DVD to VCR Setting a Disc to Protect VR DVD-RW To prevent accidental over-recording, editing or erasing of recordings, you can protect them using the Setting menu. Recording Insert a recordable disc. 1 2 3 4 In stop mode, press [SET UP]. "Easy Setting Menu" or "Advanced Setting Menu" will appear. Select "Disc" using [Cursor U / D], then press [ENTER]. Select "Disc Protect OFF ON" using [Cursor U / D], then press [ENTER]. Select "Yes" using [Cursor U / D], then press [ENTER]. The disc is protected. 5 Select "DVDVCR" using [Cursor U / D], then press [ENTER]. Dubbing Mode VCR DVD DVD VCR VCR DVD Note · The Disc Protect setting is available only when a disc recorded in VR mode is inserted. · You can select only "Disc Protect ON OFF" when a protected disc is inserted. To cancel the disc protect: · Select "Disc Protect ON OFF" at step 3, then select "Yes. " · If you insert a disc protected with this unit, "Disc Protect ON OFF" will appear instead of "OFF ON. " 6 7 Press [SET UP] to exit the setting menu. Press [VCR]. Make sure to select a recording speed using [REC SPEED]. (See page 64. ) Rewind or fast forward the tape to the point where you want to start recording. 8 9 Press [DVD]. Press [DVD PLAY P] on the unit, and then press [PAUSE p] at the point you wish to start recording. DVD to VCR duplication will start. 10 Press [DUBBING]. 35 EN Finalising Discs Video VR If "No" is selected and [ENTER] or [RETURN] is pressed, finalising is continued. You cannot cancel finalising a DVD-R disc once it has started. DVD-RW DVD-RW DVD-R You will need to finalise discs to play them back in other players. Finalising may take from several minutes up to an hour. [. . . ] Finalise To make DVDs that have been recorded playable in DVD players. It is possible to finalise DVD-R / DVDRW discs with this unit. JPEG (Joint Photographic Experts Group) JPEG is a method of compressing still image files. You can copy JPEG files on CD-RW / R discs from a computer and play back the files on this unit. [. . . ]