User manual JVC DT-V100CG

[. . . ] MULTI-FORMAT MONITOR DT-V100CG INSTRUCTIONS The supplied wide mask is attached to the monitor in the illustration on the right. LCT1811-001A Thank you for purchasing this JVC Multi-Format Monitor. Before using it, read and follow all instructions carefully to take full advantage of the monitor's capabilities. SAFETY PRECAUTIONS In order to prevent any fatal accidents caused by misoperation or mishandling the monitor, be fully aware of all the following precautions. WARNINGS To prevent fire or shock hazard, do not expose this monitor to rain or moisture. Dangerous high voltages are present inside the unit. Do not remove the back cover of the cabinet. [. . . ] Green: Shows the HD SDI signal is input. Orange: Shows the composite signal is input.  page 19 REMOTE SYSTEM Sets the MAKE/TRIGGER terminal.  "How to Use the MAKE/TRIGGER Terminal" on page 19 CONTROL FORM: Selects the control system for the MAKE/TRIGGER terminal. MAKE: Selects the make contact system as the external control method. TRIG. : Selects the trigger system as the external control method. SET: You can apply the functions to the 1st to 6th pin terminals of the MAKE/TRIGGER terminal as you want. PORT F1 ­ PORT F6: Selects the function to be applied to the 1st to 6th pin terminals of the MAKE/TRIGGER terminal.  "How to Use the MAKE/TRIGGER Terminal" on page 19 NOTE: You can set "PORT F1" ­ "PORT F6" only when "CONTROL FORM" is set to "SET. " COLOR SYSTEM Selects the color system. AUTO:Changes NTSC and PAL automatically. PAL: Keeps the color system PAL. NOTE: Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL. SYNC SELECT Selects the synchronized signal. INT. : The input video signal is synchronized with the built-in sync signal. EXT. : The input video signal is synchronized with an external signal from an external sync terminal. RUSH DELAY TIME Sets the delay time between when the stand-by button is pressed and when the monitor actually turns on. STD. : Power turns on about 1 second after the stand-by button is pressed. SLOW: Power turns on about 3. 2 seconds after the standby button is pressed. ZOOM WINDOW Adjusts the horizontal position of the zooming area. This item appears on the menu only when using the Component Unit (option). · ­30 O 00 O +30 ­: Moves the horizontal position of the zooming area to the left. +: Moves the horizontal position of the zooming area to the right. NOTE: It is recommended to apply "SLOW" to some of the monitors if you need to turn on multiple monitors at the same time. You can control the rush current of the entire system. TALLY SELECT Selects the color of the tally lamp on the upper right of the front panel. GREEN:The tally lamp lights in green. RED: The tally lamp lights in red. NOTES: · "TALLY SELECT" does not appear on the menu when both the following conditions are applied: ­ When selecting "TA. SEL" to a pin terminal of the MAKE/ TRIGGER terminal in "REMOTE SYSTEM" of SET-UP MENU. ­ When activating the external control.  page 19 · The tally lamp is controled using the MAKE/TRIGGER terminal of the REMOTE (external control) terminals. AUDIO GROUP Sets the group of the available audio output modes selected by the MENU control. This item appears on the menu only when using the Multi-Format SDI Unit (option). 1G: 2G: 1-2G: 1ch 2ch 3ch 4ch 1-2ch 3-4ch 1-4ch 5ch 6ch 7ch 8ch 5-6ch 7-8ch 5-8ch 1ch 2ch 3ch 4ch 5-8ch 5ch 1-4ch 6ch 7ch 8ch 5-6ch 1-2ch 3-4ch AUTO 7-8ch · When HD/SD SDI signal including EMBEDDED AUDIO signal is input, you can select the channel of the audio signal output from the audio output terminal by changing the audio output mode. Refer also to the Multi-Format SDI unit's manual. 15 How to Use SET-UP MENU (cont. ) HOUR METER X100h Displays the total usage time of the monitor in hundred-hour units. · 000 O 655 NOTES: · When the timer passes 655, it returns to 000. [. . . ] · You may sometimes experience a mild electric shock when you touch the picture tube. This phenomenon is due to a normal buildup of static electricity on the CRT and is not harmful. · The monitor emits a strange sound when the room temperature changes suddenly. This is only a problem if an abnormality appears on the screen as well. [. . . ]