User manual JVC EX-70

[. . . ] COMPACT COMPONENT SYSTEM CA-EX70 Consists of RX-EX70 and XL-EX70. RX-EX70 RM­SEEX90U REMOTE CONTROL INTEGRATED AMPLIFIER / TUNER VOLUME BAND POWER 1 2 3 SLEEP 4 5 6 S. BASS AUX DIRECT INPUT DOWN UP PHONES 7 8 9 FM MODE /MUTING TUNER STANDBY 10 PLAY MODE +10 REPEAT CD KEY MODE POWER CD 1 CD 2 CD 3 TAPE DIRECT S. A. BASS TREBLE BA SS BALANCE INTEGRATED AMPLIFIER/TUNER RX-EX70 CL O /TIM CK ER ­/L +/ R SE T CA E NC L D IR TA EC P E TIO N XL-EX70 COMPACT DISC PLAYER L PERO TANT O C /CANCEL CD 3 VOLUME PLAY & EXCHANGE CD 2 CD 1 M FA UD TIN E G EC E R US PA STANDBY REPEAT PLAY MODE POWER COMPACT DISC PLAYER XL-EX70 INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. [. . . ] If this happens, start again from step 2. 4 Press SET again. SE T "MEMORY" is displayed and the station is stored at the selected preset number. If another station was previously stored at that preset number, that station is erased and the new station is memorized in its place. 25 CA-EX70 Listening to Preset Stations This section explains how to tune in preset stations. From the front panel KEY MODE 1 Press KEY MODE so that "PRESET" appears in the display. 2 Press > (for higher numbers) or < (for lower numbers) repeatedly to select the preset you desire. From the remote control You can tune in the preset stations from the remote control either, by switching through the presets one by one, or by specifying the preset you desire. TUNER 1 Press TUNER to select the tuner operations. In addition to selecting the FM band, this operation also sets the remote control to tuner operation mode. The remote control must be set to the tuner operation mode before proceeding to the following steps, even if the band was previously set to FM using the controls on the front panel. 2 Select the preset station you desire. To switch through the preset stations one by one Press > (¢ ¡) (for higher numbers) or < (4 1) (for lower numbers) repeatedly to select the preset number you desire. To specify the preset stations Use the number buttons to select a preset number. · For preset number 15, press +10 then 5. · For preset number 20, press +10 then 10. · For preset number 30, press +10, +10, then 10. 26 CA-EX70 CD Operations Loading CDs The CD player's unique 3 disc changer mechanism houses 3 individual disc trays inside the main tray. CD 3 CD 2 CD 1 1 Press 0 (open) for the disc tray (CD 1to 3) you want to load. The main tray opens to the selected disc tray. The disc tray number and "OPEN" appear in the display. Example) When CD1 0 is pressed · The disc trays housed in the main tray are numbered CD 1, CD 2, and CD 3 starting from the bottom tray. One touch operation When the unit is in the STANDBY mode, press one 0 to automatically turn the power on and open to the selected tray. 2 Place a CD with the label side facing up. Place CD singles (8 cm) in the depressed inner circle. 3 Press the same 0 you pressed in step 1. The main tray closes. The disc tray number and "CLOSE" appear in the display. Example) When CD 1 0 is pressed · Repeat steps 1 to 3 to load up to 3 CDs. Displayed information When a CD is loaded, the disc number for that CD is displayed and the player reads the disc's data. After the data is read, the display shows the total number of tracks and total playing time of the disc, then switches to show the playing time for the first track. DISC DISC Reading data Total number of tracks and total playing time (shown for 4 seconds) Playing time for track 1 DISC Likewise, when playback is stopped, the display shows the total number of tracks and total playing time of the current disc for 4 seconds, then it shows the playing time for track 1. Tip When loading more than one CD, instead of closing the main tray, press 0 for the next tray you want to load, the main tray automatically closes and then reopens to selected disc tray. CAUTION The disc tray will close if pushed inward. Be careful not to push the tray inward when placing a CD. 27 CA-EX70 Basic Operations The following operations play all 3 CDs once, one after another. 1 Load CDs. See "Loading CDs" on page 27. CD 3 CD 2 CD 1 2 Press CD 1, CD 2 or CD 3 for the disc you want to play. The amplifier/tuner automatically switches to the CD input and the CD starts to play. The < indicator lights up. Lights DISC /CANCEL Press </8 instead of CD 1, CD 2 or CD 3 to start playing the CD whose disc number appears in the display. One touch operation When the unit is in the STANDBY mode, press CD 1, CD 2 or CD 3 or </8 to automatically turn on the power to the CD player and amplifier/tuner, set the amplifier/tuner to the CD input and start playing the CD. CD playback sequence When 3 CDs are loaded, they are played in one of the following sequences. When CD 1 is pressed CD 1 ] CD 2 ] CD 3 (then stops) When CD 2 is pressed CD 2 ] CD 3 ] CD 1 (then stops) When CD 3 is pressed CD 3 ] CD 1 ] CD 2 (then stops) * When only 2 CDs are loaded, they play in the same order, but the disc tray without a CD is skipped. To stop playback /CANCEL Press &/CANCEL. When playback is stopped, the display shows the total number of tracks and total playing time of the current disc for 4 seconds, then it shows the playing time for track 1. To pause playback /CANCEL Press </8. Press again to resume playback from the position where it was paused. CD 3 CD 2 CD 1 To remove a CD: Press the respective 0. 28 CA-EX70 To exchange CDs during playback of another Press 0 corresponding to a disc number not shown in the display to open that disc tray and exchange the CD. When CDs are exchanged during playback, playback stops after playing the last exchanged CD. To skip to the beginning of a track Press ¢ once to skip to the beginning of the next track. Press 4 once to skip to the beginning of the current track. · Each additional press skips to another track. To check the playing time of a track Press 4 or ¢ during stop mode to display the desired track number. [. . . ] WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800)537-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus and letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department. [. . . ]