User manual JVC FS-SD7R

[. . . ] COMPACT COMPONENT SYSTEM FS-SD5R/FS-SD7R/FS-SD9R REMOTE CONTROL DIMMER SLEEP DISPLAY AUTO PRESET FM MODE PROGRAM RANDOM DOOR SLIDE REPEAT AHB PRO CD BASS TREBLE CANCEL PTY/EON DISPLAY MODE UP SET DOWN FADE MUTING MD/AUX CD FM / AM VOLUME FS-SD5R REMOTE CONTROL DIMMER SLEEP DISPLAY AUTO PRESET FM MODE PROGRAM RANDOM DOOR SLIDE REPEAT AHB PRO CD BASS TREBLE CANCEL PTY/EON DISPLAY MODE UP SET DOWN FADE MUTING MD/AUX CD FM / AM VOLUME FS-SD7R, FS-SD9R INSTRUCTIONS For Customer Use: Enter below the Model No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference. Serial No. LVT0418-002A [B/UB] Warnings, Cautions and Others IMPORTANT for the U. K. DO NOT cut off the mains plug from this equipment. [. . . ] Turn the AM loop antenna for best reception. 2 Select a station using one of the following methods. q Manual Tuning Press the 4 or button on the Unit or the Remote Control repeatedly to move from frequency to frequency until you find the station you want. OR 11 Using the Tuner Presetting Stations You can preset up to 30 FM stations and up to 15 AM (MW/ LW) stations using the Remote Control. Auto Presetting In each band, you can automatically preset FM-30, AM-15 (MW/LW) stations. Preset numbers will be allocated as stations are found, starting from the lowest frequency and moving up the frequency. AUTO PRESET FM / AM Preset numbers may have been set to factory test frequencies prior to shipment. You can preset the stations you want into memory by following one of the presetting methods below. (for 2 seconds) Manual Presetting SET FM / AM 1 STORED UP DOWN SET SET Select a band by pressing the FM/AM button. Press the AUTO PRESET button on the Remote Control for more than two seconds. Repeat steps 1-2 for the other band. 2 3 or When changing the Band FM = 30, AM = 15 1 2 3 Select a band by pressing the FM/AM button. Press the 4 or button to tune in a station. Press the SET button. "SET" will blink for 5 seconds. Within 5 seconds, proceed to the next step. When the display returns to the one set in step 2 after 5 seconds, press the SET button again. s If you want to change the preset stations, carry out the Manual Presetting for the desired preset numbers. CAUTION: Even if the system is unplugged or if the power failure occurs, the preset stations will be stored for about 24 hours. However, in case the preset stations are erased, you will need to preset the stations again. 4 Press the UP, DOWN, >, or < button within 5 seconds to select the preset number. UP or DOWN button:Increase or decrease the preset number by 1. Pressing and holding the button will continuously increase or decrease the preset number. > or < button: Increase or decrease the preset number by 1. Pressing and holding the button will rapidly increase or decrease the preset number. To Change the FM Reception Mode When you are tuned into an FM stereo broadcast, the "STEREO" indicator lights up and you can hear stereo effects. If an FM stereo broadcast is hard to receive or noisy, you can select Monaural mode. Reception improves, but you lose stereo effect. Press the FM MODE button on the Remote Control so that the "MONO" indicator lights up on the display. FM MODE 5 6 Press the SET button within 5 seconds. "STORED" appears and after 2 seconds, the display returns to the broadcast frequency display. MONO Repeat above steps 1 to 5 for each station you want to store in memory with a preset number. To change the preset stations, repeat the same steps as above. To restore the stereo effect, press the FM MODE button on the Remote Control so that the "MONO" indicator goes off. 12 Using the Tuner Receiving FM Stations with RDS You can use the RDS (Radio Data System) by using the buttons on the Unit or the Remote Control. RDS allows FM stations to send additional signals with their regular programme signals. For example, the stations send their station names, and information about what type of programmes they broadcast, such as sports or music, etc. This unit can receive the following types of RDS signals: PS (Programme Service): shows commonly known station names. PTY (Programme Type): shows types of broadcast programmes. RT (Radio Text): shows text messages the station sends. What information can RDS signals provide?The display shows RDS signal information that the station sends. PS (Programme Service): While searching, "PS" appears, then station name is displayed. [. . . ] Avoid exposure to direct sunlight, temperature extremes, and moisture. If a CD does become dirty, wipe it with a soft cloth in a straight line from center to edge. If there are fingerprints, etc. on the lens, gently wipe clean with a cotton swab. CAUTION: Do not use any solvent (for example, conventional record cleaner, spray thinner, benzine, etc. ) to clean a CD. Moisture Condensation Moisture may condense on the lens inside the System in the following cases: After turning on heating in the room. If the System is brought directly from a cold to a warm place. [. . . ]