User manual JVC GD-V500PZU-GD-V500 Instruction Manual

[. . . ] WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock do not remove cover or back. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons. The exclamation point within a triangle is intended to tell the user that important operating and servicing instructions are in the papers with the appliance. WARNING: To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or moisture. Do not place containers with water (flower vase, cups, cosmetics, etc. ) above the set. [. . . ] Unplug the cord from the wall outlet and clean it with a dry cloth. Cleaning and maintenance The front of the display panel has been specially treated. Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode. 7 8 7 Accessories Accessories Supplied Requires two AA batteries. Remote Control Transmitter EUR646526 INPUT Remote Control Batteries 2. Install the batteries as shown in the battery compartment. (Polarity + or ­ must match the markings in the compartment). 3. Replace the cove and slide in reverse until the lock snaps. Operating Instruction book Batteries for the Remote Control Transmitter (AA(R6) Battery × 2) SURROUND VOL N R PICTURE SOUND SET UP GD-V500PZU PICTURE POS. /SIZE ASPECT PC OFF TIMER PLASMA DISPLAY Two "AA" size RCA/BNC Adapter Plug Helpful Hint: For frequent remote control users, replace old batteries with Alkaline batteries for longer life. Optional Accessories Precaution on battery use · Speakers TS-C5000SPG TS-C50P1G · Stand Unit Incorrect installation can cause battery leakage and corrosion that will damage the remote control transmitter. Batteries should always be replaced as a pair. Always use new batteries when replacing the old set. Do not combine a used battery with a new one. Do not mix battery types (example: "Zinc Carbon" with "Alkaline"). Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display. · Wall Mounting Unit TS-C50P6G · Wall Mounting Unit (angled) TS-C50P2G · Ceiling Suspension Unit TS-C50P3G For assembling Full instructions are supplied with each optional accessories for use with this Plasma Display Monitor. 9 10 GD-V500PZU 8 GD-V500PZU Basic Controls R - STANDBY G POWER ON INPUT VOL Connections ­ + Main Power On/Off Switch Power Indicator The Power Indicator will light. Input button (VIDEO (S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Push the "INPUT" button to select VIDEO(S-VIDEO)/COMPONENT or RGB/PC input signal modes sequentially. Volume Adjustment Push the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. · Power-OFF . . . . Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet. ) · Stand-by . . . . Green Stand-by (ON/OFF) button The Plasma Display Monitor must first be plugged into the wall outlet and turn on at the power switch (see page 18). Push this button to turn the Plasma Display Monitor ON, from STANDBY mode. Push it again to turn the Plasma Display Monitor OFF to STANDBY mode. Status button Push the "Status" button to display the current system status. SURROUND button (see page 27) Input button (VIDEO(S-VIDEO)/COMPONENT, RGB/PC Mode Selection) Press to select VIDEO(S-VIDEO)/ COMPONENT or RGB/PC input signal modes sequentially. (see page 19) INPUT SPEAKER Terminals (R) SPEAKER Terminals (L) VIDEO NORMAL 1 2 Sound mute On/Off (see page 26) Volume Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 3 VOL 90 1 VIDEO(S-VIDEO)/COMPONENT, RGB/PC mode 2 Aspect mode (see page 22) 3 Off timer The off timer indicator is displayed only when the off timer has been set. N R ­ Cable fixing bands Secure any excess cables with bands, as required. [. . . ] Press If the picture image becomes unstable: With the system set on Auto, under conditions of low level or noisy input signals the image may in rare cases become unstable. Should this occur, set the system to match the format of the input signal. SIGNAL 3D Y/C FILTER (NTSC) COLOR SYSTEM AUTO (4:3) ON AUTO NORMAL RETURN CHANGE SELECT (store) button [ VIDEO ] The following operation methods are the same for both the SIGNAL [RGB] and SIGNAL [PC]. H&V SYNC NARROW PULL-IN RANGE CLAMP POSITION H-FREQ. 60. 0 Hz SIGNAL [ PC ] H&V SYNC NARROW PULL-IN RANGE CLAMP POSITION H-FREQ. 60. 0 Hz SYNC Setting RGB sync signal setting: Confirm that the input is set to RGB INPUT (this setting is valid only for RGB INPUT). [. . . ]