User manual JVC GD-V501U-GD-V501 Instruction Manual

[. . . ] PLASMA DISPLAY MONITOR GD-V501U INSTRUCTIONS For customer Use: Enter below the Model No. which is located on the rear panel of the cabinet. Retain this information for future reference. Model No. Serial No. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. Refer servicing to qualified service personnel. [. . . ] Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. Battery replacement is necessary when the remote control acts sporadically or stops operating the Plasma Display set . 9 Basic Controls R - STANDBY G POWER ON INPUT ­ VOL + · · · INPUT button Power Indicator (VIDEO (S VIDEO), COMPONENT/RGB The Power Indicator will light. and PC Mode Selection) POWER-OFF Indicator not illuminated Press the "INPUT" button to select (The unit will still consume some power VIDEO (S VIDEO), COMPONENT/RGB as long as the power cord is inserted and PC input signal modes sequentially. into the wall outlet. ) (see page 19) STAND-BY . . . . . Red POWER-ON. . . . . Green Main POWER ON/OFF Switch VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. STAND-BY (ON/OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch. (see page 18) Press this button to turn the Plasma Display ON, from STANDBY mode. Press it again to turn the Plasma Display OFF to STAND-BY mode. STATUS button Press the "STATUS" button to display the current system status. VIDEO NORMAL SURROUND button (see page 27) INPUT button (VIDEO (S VIDEO), COMPONENT/ RGB and PC Mode Selection) Press to select VIDEO (S VIDEO), COMPONENT/RGB and PC input signal modes sequentially. (see page 19) INPUT 1 2 Sound mute On/Off (see page 26) VOLUME Adjustment Press the Volume Up "+" or Down "­" button to increase or decrease the sound volume level. SURROUND OFF TIMER 90 3 1 VIDEO (S VIDEO), COMPONENT/RGB, PC mode 2 ASPECT mode (see page 22) 3 OFF TIMER The OFF TIMER indicator is displayed only when the off timer has been set. N button (see page 25, 26, 28, 29) PICTURE button (see page 28) VOL N R R button (see page 21) ACTION button Press to make selections POSITION buttons SET UP button (see page 20) SOUND button (see page 26) ASPECT PICTURE SOUND SET UP PICTURE POS. /SIZE PICTURE POS. /SIZE button (see page 24) PC OFF TIMER ASPECT button Press to adjust the aspect. (see page 22) PC button Press the "PC" mode selection button to select the PC mode. OFF TIMER button This button is used to switch The Plasma Display can be preset to switch to stand-by after a fixed period. setting changes to 30 minutes, 60 minutes, 90 minutes and 0 minutes (off timer cancelled) each time the button is pressed. 30 60 90 When three minutes remain, "Off timer 3" will flash. The off timer is cancelled if a power interruption occurs. 0 10 Connections SPEAKER Terminals (R) SPEAKER Terminals (L) AC cord connection (see page 18) ­ Cable fixing bands Secure any excess cables with bands, as required. Pass the attached cable fixing band through the clip as shown in the figure. To secure cables connected to Terminals, wrap the cable fixing band around them then pass the pointed end through the locking block, as shown in the figure. While ensuring there is sufficient slack in cables to minimize stress (especially in the power cord), firmly bind all cables with the supplied fixing band. 1 To tighten: 2 To loosen: Push the catch Pull Pull AUDIO R AUDIO IN L S VIDEO IN VIDEO IN VIDEO OUT R AUDIO L VD HD PR/CR/R PB/CB/B Y/G AV COMPONENT/RGB IN PC IN SERIAL AV Terminals (see page 12, 13) COMPONENT/RGB IN and Audio IN Terminals (see page 14) From EXIT monitor Terminal on Computer (see page 15) From SERIAL Terminal on Computer (see page 17) 11 Connections Speakers connection When connecting the speakers, be sure to use only the optional accessory speakers. Refer to the speaker's Installation Manual for details on speaker installation. Speakers (Optional accessories) 1 2 1 2 AV Input Terminals connection Connect the signal source equipment (see page 14 to 17). (Example) When connecting an S VIDEO VCR (S VIDEO VCR) R Audio OUT L Video OUT S Video OUT S VIDEO 4 pin socket Luminance earth Chrominance earth 2×RCA audio cables AUDIO Audio input to L/R sockets S VIDEO Video input to S VIDEO socket Luminance in Chrominance in R AUDIO IN L S VIDEO IN VIDEO IN VIDEO OUT AV Note: Additional equipment and cables shown are not supplied with this set. 12 Connections AV Input connection VIDEO signal connection (VCR) R Audio OUT L Video OUT VIDEO RCA-BNC video cable AUDIO 2×RCA audio cables Video input to BNC socket Audio input to L/R sockets R AUDIO IN L S VIDEO IN VIDEO IN VIDEO OUT AV (VCR) R Audio OUT L Video OUT VIDEO RCA video cable Video input to BNC socket RCA-BNC adapter plug AUDIO 2×RCA audio cables Audio input to L/R sockets Notes: (1) The S Video input will override the composite video signal when S Video lead is connected. [. . . ] · NTSC signal input during "VIDEO (S VIDEO)" input signal mode. · 525i(480i) signal input during "COMPONENT" input signal mode. R 3D Y/C FILTER (NTSC) COLOR SYSTEM 3:2 PULLDOWN ASPECT AUTO (4:3 ) SIGNAL Press to exit from adjust mode. 3:2 PULLDOWN 35 SET UP for Input Signals SYNC Select SIGNAL from the "SET UP" menu during RGB or PC input signal mode. Press to select each item. SET UP COMPONENT/RGB-IN SELECT RGB SIGNAL SCREENSAVER ENGLISH (US) OSD LANGUAGE SET UP TIMER Press SIGNAL SYNC R (ACTION) button [ RGB ] H&V H-FREQ. V-FREQ. 31. 5 kHz 60. 0 Hz [ PC ] H&V Press to exit from adjust mode. SIGNAL SYNC H-FREQ. [. . . ]