User manual JVC GM-V42E

[. . . ] PLASMA DISPLAY MONITOR BEDIENUNGSANLEITUNG : PLASMABILDSCHIRM MANUEL D'INSTRUCTIONS : MONITEUR DE VISUALISATION PLASMA MANUALE D'ISTRUZIONI : MONITOR CON SCHERMO AL PLASMA MANUAL DE INSTRUCCIONES : MONITOR DISPLAY DE PLASMA MENU INPUT LCT1595-001A-U ESPAÑOL GM-V42E GM-V42EB INSTRUCTIONS ITALIANO FRANÇAIS DEUTSCH ENGLISH Model GM-V42E GM-V42EB Thank you for purchasing this JVC Monitor. Before using the monitor, read this manual carefully so that you know how to use the Monitor correctly. Refer to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions. [. . . ] · When adjusting the size, the size cannot be adjusted proportionally, but can be enlarged rightward (or downward) only and reduced leftward (or upward) only. Therefore, it is necessary to adjust both the size and position alternately to adjust to the appropriate size. 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU *1 Size and position adjustments are so related that if one is adjusted much, the other's adjustable range will be reduced. *2 DOT CLOCK is the function to adjust the pixel sampling number of the A/D converter to the resolution (the vertical pixel number) of the input signal. CLOCK PHASE is the function to adjust the sampling timing (phase) to the phase of the input signal. You can use the two functions to reduce flickering and blurring on the screen when using the RGB A or RGB B input. 5 Press 2/3 to adjust the selected item. Note: · During size and position adjustments, the Monitor screen may be distorted. This is normal, but not a malfunction of the Monitor. Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY ENTER: SELECT: EXIT: MENU 2 Press 5/ to move the cursor (3) to "SIZE/POSITION ADJ. " 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. (To be continued on the next page) 17 ENGLISH Video Adjustments (Continued) To make an adjustment while viewing the adjustment bar After step 3 on page 17, proceed as follows: 1 Press 5/ to move the cursor (3) to "sub menu. " 2 Press 3 to display the Sub Menu. The Sub Menu for H SIZE appears on the screen. H SIZE ++ :+01 ++ MENU INPUT 3 Press 5/ to select the Sub Menu you want to adjust. Each time you press the button, the Sub Menu changes as follows: H SIZE H POSITION V SIZE CLOCK PHASE DOT CLOCK V POSITION 4 Press 2/3 to adjust the selected item. 5 Repeat steps 3 and 4 to adjust the other items. 6 Press MENU/EXIT (or MENU on the Monitor) three times to exit from the menu operations. MENU INPUT To reset the adjustments After step 3 on page 17, proceed as follows: 2/3 5 A B MUTING 5/ MENU 1 Press 5/ to move the cursor (3) to "reset. " 2 Press 3. The confirmation screen appears. reset Are you sure?"YES" then "NO" then MENU key. 3 Press 3 again to reset the adjustments. RM­C579 REMOTE CONTROL UNIT To cancel the reset, press MENU/EXIT (or MENU on the Monitor). Note: · Adjustment values for both horizontal and vertical sizes of the screen are so related that if one is adjusted up to near the maximum value, the attainable value of the other will be decreased. OFF DISPLAY POWER ON ASPECT INPUT SELECT COMPO. /(RGB B) VIDEO RGB A VOLUME VOLUME ­ 2/3 5/ MENU/EXIT MENU/EXIT 18 5 Adjusting the Color Temperature The adjusted setting applies to all inputs. Adjusting the White Balance 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU 1 Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY On the remote control: Press MENU/EXIT while holding VOLUME ­ to display the Setup Menu. On the Monitor: Press MENU while holding 2 to display the Setup Menu. SET-UP MENU 1/2 : : : : OFF OFF ENTER: SELECT: EXIT: MENU 2 3 Press 5/ to move the cursor (3) to "FUNCTION SELECT. " Press 3 to display the Function Selection Menu. FUNCTION SELECT COLOR TEMP. reset : : : : : H I G H* PANORAMIC AUTO RGB HIGH Cursor (3) STATUS DISPLAY CONTROL LOCK REMOTE SWITCH HD SIGNAL MODE WHITE BALANCE TIMER MODE1 1080i ADJUST: SELECT: EXIT: MENU ADJUST: SELECT: EXIT: MENU " * " appears only when you have adjusted the White Balance (see the right column). 2 Press 5/ to move the cursor (3) to "WHITE BALANCE. " · The Setup Menu consists of two pages. If you keep pressing 5/, you can move to the other page from the current page. 4 5 Press 5/ to move the cursor (3) to "COLOR TEMP. " Press 2/3 to make an adjustment. Each time you press the button, the color temperature alternates between "HIGH" and "LOW. " HIGH: LOW: To make the screen become bluish. To make the screen become reddish. 3 Press 3 to display the White Balance Adjustment Menu. WHITE BALANCE:HIGH R GAIN G GAIN B GAIN sub menu reset : 000 :+ 001 :­ 002 ADJUST: SELECT: EXIT: MENU 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. 4 5 6 7 Press 5/ to move the cursor (3) to the item you want to adjust. Repeat steps 4 and 5 to adjust the other items. Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. Note: · To make a fine adjustment, adjust "WHITE BALANCE" (see the right column). Notes: · Adjustable range will vary among the Monitors. · "MAX" may appear soon after you begin adjustment. [. . . ] ­ After cleaning, switch on the Monitor's main power again. If self-diagnostic lamps do not go off, consult your dealer immediately. Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual. Self-diagnostic Report Sheet Store name where you purchased the Monitor If the screen monitor dims a little and "TEMP. [. . . ]