User manual JVC GM-X50U-GM-X50 Instruction Manual

[. . . ] PLASMA DISPLAY MONITOR GM-X50U INSTRUCTIONS For Customer Use: Enter below the Model No. which is located on the rear panel of the cabinet. Retain this information for future reference. Model No. Serial No. MENU INPUT LCT1601-001A INSTRUCTIONS Model GM-X50U Thank you for purchasing this JVC Monitor. Before using the monitor, read this manual carefully so that you know how to use the Monitor correctly. [. . . ] To cancel the reset, press MENU/EXIT (or MENU on the Monitor). Note: · Adjustment values for both horizontal and vertical sizes of the screen are so related that if one is adjusted up to near the maximum value, the attainable value of the other will be decreased. 5 Press 2/3 to adjust the selected item. Note: · During size and position adjustments, the Monitor screen may be distorted. This is normal, but not a malfunction of the Monitor. 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. 18 Adjusting the Color Temperature The adjusted setting applies to all inputs. Changing the Aspect Ratio 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY Cursor (3) EXIT: MENU PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY ENTER: SELECT: ENTER: SELECT: EXIT: MENU 2 3 Press 5/ to move the cursor (3) to "FUNCTION SELECT. " Press 3 to display the Function Selection Menu. FUNCTION SELECT COLOR TEMP. ASPECT SIGNAL MODE COMPO. /RGB B SYNC TERM. reset : : : : : H I G H* PANORAMIC AUTO RGB B HIGH 2 3 Press 5/ to move the cursor (3) to "FUNCTION SELECT. " Press 3 to display the Function Selection Menu. FUNCTION SELECT COLOR TEMP. ASPECT SIGNAL MODE COMPO. /RGB B SYNC TERM. reset : : : : : H I G H* PANORAMIC AUTO RGB B HIGH ADJUST: SELECT: EXIT: MENU *1 *2 *3 " * " appears only when you have adjusted the White Balance (see the right column). *1 "ASPECT" does not appear when 720/60p, 720/50p, 1080/60i (1035/60i), or 1080/50i signal is being input through the COMPONENT/RGB B input terminals. *2 "SIGNAL MODE" appears only when VIDEO A, VIDEO B, or COMPONENT input is selected. *3 "SYNC TERM. " appears only when the RGB B input is selected. ADJUST: SELECT: EXIT: MENU *1 *2 *3 *1 "ASPECT" does not appear when 720/60p, 720/50p, 1080/60i (1035/60i), or 1080/50i signal is being input through the COMPONENT/RGB B input terminals. *2 "SIGNAL MODE" appears only when VIDEO A, VIDEO B, or COMPONENT input is selected. *3 "SYNC TERM. " appears only when the RGB B input is selected. 4 5 Press 5/ to move the cursor (3) to "COLOR TEMP. " Press 2/3 to make an adjustment. Each time you press the button, the color temperature alternates between "HIGH" and "LOW. " HIGH: LOW: To make the screen become bluish. To make the screen become reddish. 4 5 Press 5/ to move the cursor (3) to "ASPECT. " Press 2/3 to select an aspect ratio you want. Each time you press the button, the aspect ratio changes as follows: REGULAR FULL PANORAMIC ZOOM * For detailed information on these aspect ratios, see page 15. 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. Note: · To make a fine adjustment, adjust "WHITE BALANCE" (see page 25). 6 Press MENU/EXIT (or MENU on the Monitor) twice to exit from the menu operations. Note: · When one of the following signals is being input, you cannot select the aspect ratio you want. I 720/60p, 720/50p, 1080/60i (1035/60i), or 1080/50i signal through the COMPONENT/RGB B input terminals Aspect ratio is fixed to FULL ("ASPECT" does not appear on the display). I When any signal other than RGB15K-60 and RGB15K-50 through the RGB A or COMPONENT/RGB B input terminals You can select only REGULAR and FULL. 19 ENGLISH The setting adjusted applies to all inputs. · You can change the aspect ratio by pressing ASPECT. (See page 15. ) Video Adjustments (Continued) Setting the Receivable Signal Types You can set the receivable signal types. Normally, select "AUTO. " A common setting will apply to both the VIDEO A input and the VIDEO B input, and a different setting will apply to the COMPONENT input. Setting the COMPONENT/RGB B Input After connecting the playback device such as a PC or a DVD player to the COMPONENT/RGB B terminals, you have to specify which type of signal comes into this terminal--RGB or component signals. · Without setting "COMPO. /RGB B" correctly, you cannot show any picture though you select the COMPONENT or RGB B input. 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU 1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu. MAIN MENU Cursor (3) PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY Cursor (3) ENTER: SELECT: EXIT: MENU PICTURE ADJ. FUNCTION SELECT STATUS DISPLAY 2 3 Press 5/ to move the cursor (3) to "FUNCTION SELECT. " Press 3 to display the Function Selection Menu. FUNCTION SELECT COLOR TEMP. [. . . ] ­ After cleaning, switch on the Monitor's main power again. If self-diagnostic lamps do not go off, consult your dealer immediately. Note: If you switch on the main power immediately after switching it off (or after recovering from a brief power interruption), the self-diagnostic lamps may light (or flash), and no image may appear on the screen. In this case, switch off the main power again, wait for about 10 seconds, then switch it on again. If no self-diagnostic lamps light or flash, you can operate and use the Monitor as usual. Self-diagnostic Report Sheet Store name where you purchased the Monitor If the screen monitor dims a little and "TEMP. [. . . ]