User manual JVC GR-AXM710U-GR-AXM710

[. . . ] COMPACT VHS CAMCORDER GR-AXM710 ENGLISH For Customer Use: Enter below the Model No. which is located on the bottom of cabinet. Retain this information for future reference. INSTRUCTIONS Model No. Serial No. LYT0253-001B EN 2 EN Dear Customer, Thank you for purchasing the JVC Compact VHS camcorder. [. . . ] Load the cassette adapter into the VCR and play the tape back as you would any other. Slide the latch and the compartment door opens automatically. Do not attempt to force the adapter open. Then, insert your finger in the hole on the underside of the adapter as shown in the illustration at left, and push up and remove the cassette. 2 INSERT CASSETTE IN ADAPTER 3 PLAY BACK ON CONNECTED VCR 4 REMOVE CASSETTE FROM ADAPTER Sliding latch Compact video cassette NOTES: Reels During tape loading and unloading, do not touch the reels for safety and tape protection. During special-effect playback (slow motion, still frame, etc. ), the picture may vibrate or noise bars may appear on the screen. To record on a VCR using a compact cassette and the adapter, cover the adapter's recording safety hole with adhesive tape. Recording safety hole 50 EN PLAYBACK Basic Connections And Tape Dubbing These are some basic types of connections. When making connections, refer also to your VCR and TV instruction manuals. A. Connection to a TV or VCR equipped with an S-VIDEO Basic Connections Use optional Video and Audio cables. TV To Video Output Video cable (optional) To VIDEO IN To TV or VCR Audio cable (optional) To Audio Output To AUDIO IN VCR Connector cover* A. Connection to a Connection For Tape DubbingTV or VCR equipped with an S-VIDEO Use optional Video and Audio cables. Power Switch PLAY/PAUSE (4/6) Button TV To Video Output Video cable (optional) Audio cable (optional) To VIDEO IN VCR (Recording deck) To AUDIO IN To Audio Output Connector cover* * When connecting the cables, open this cover. EN51 Basic Connections Make sure the camcorder's power is off. Tape Dubbing Following the illustration on pg. Set the camcorder's Power Switch to "PLAY", turn on the VCR's power, and insert the appropriate cassettes in the camcorder and the VCR. Engage the VCR's AUX and Record-Pause modes. Engage the camcorder's Play mode to find a spot just before the edit-in point. Once it is reached, press PLAY/PAUSE (4/6) on the camcorder. 1 CONFIRM POWER-OFF STATUS 1 CONNECT EQUIPMENT 2 CONNECT CAMCORDER TO TV OR 2 PREPARE FOR DUBBING VCR Pull out the connector cover and open it. Connect as shown in the illustration ( pg. go to step 4. 3 CONNECT VCR OUTPUT TO TV INPUT Refer to your VCR's instruction manual. 3 SELECT VCR MODE 4 5 SELECT MODE NOTES: SUPPLY POWER Turn on the camcorder, the VCR and the TV. Set the VCR to its AUX input mode, and set the TV to its VIDEO mode. 4 FIND EDIT-IN POINT 5 START EDITING Press PLAY/PAUSE (4/6) on the camcorder and engage the VCR's Record mode. Engage the VCR's Record-Pause mode and press PLAY/PAUSE (4/6) on the camcorder. It is recommended to use the AC Power Adapter/ Charger as the power supply instead of the battery pack ( pg. To monitor the picture and sound from the camcorder without inserting a tape, set the camcorder's Power Switch to "CAMERA" ("AUTO" or "PRO. "), then set your TV to the appropriate input mode. Make sure you adjust the TV sound volume to its minimum level to avoid a sudden burst of sound when the camcorder is turned on. If you have a TV or speakers that are not specially shielded, do not place the speakers adjacent to the TV as interference will occur in the camcorder playback picture. 6 STOP EDITING TEMPORARILY 7 EDIT MORE SEGMENTS NOTE: Repeat steps 4 through 6 for additional editing, then stop the VCR and camcorder when finished. If you wish to dub still images recorded with the System Select Switch set to "D. S. C. ", play back the still images ( pg. 52 ­ 56) instead of doing the above steps 4 thorough 6, engage the VCR's Record mode and record them onto a tape. 52 EN D. S. C. PLAYBACK Basic Playback Still images shot using this camcoder are automatically numbered, then stored in numerical order in the built-in memory. [. . . ] WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 252-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. If you have any questions concerning your JVC Product, please contact our Customer Relations Department. [. . . ]