User manual JVC HR-DD858

[. . . ] ENGLISH SEE AUTO SET UP ON REAR SIDE CONTENTS SAFETY FIRST INSTALLING YOUR NEW RECORDER INITIAL SETTINGS 2 3 4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 VIDEO CASSETTE RECORDER HR-DD858E/EH HR-J758E/EH VCR TV SAT TV/VCR AUDIO ­ ­:­ ­ Auto Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A different time than advertised will result in no recording. VPS/PDC recording is also possible when a satellite tuner or a cable system is connected to AV2 IN/DECODER on your recorder. VPS/PDC recording is also possible via the AV1 IN/OUT connector. RETURN TO NORMAL SCREEN After confirming all information is correct, press PROG or OK. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. Repeat steps 1 ­ 9 for each additional programme. How to check if the station being received transmits a VPS/PDC signal 1 Press ­ ­:­ ­ until the channel position appears on the display panel. "VPS/PDC" appears blinking on the display panel. If a VPS/PDC signal is detected from the station, "VPS/ PDC" will stop blinking. If no VPS/PDC signal is detected from the station, "VPS/ PDC" will blink at a slower rate. 3 Press ­ ­:­ ­ or START+ again to return to normal display. ENGAGE RECORDER'S TIMER MODE Press (TIMER). The recorder turns off automatically and appears on the display panel. To disengage the timer, press (TIMER) again. To Timer-Record Weekly Or Daily Serials . anytime during steps 2 through 9, press WEEKLY (NUMBER key "9") for weekly serials or DAILY (NUMBER key "8") for daily serials (Monday ­ Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear. Timer Warning If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the recording is to start in 5 minutes. ­ WARNING­ TIMER RECORDING TO START SOON [] NOTE: You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes ( pg. 30). NOTES: The warning only appears if you're not in the Timer mode at that time. If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press . 30 EN TIMER RECORDING (cont. ) Check, Cancel And Replace Programmes ­ ­:­ ­ 1 STOP+/­ 2 5 8 0 3 2 1 4 DISENGAGE TIMER MODE Press , then press . 4 VPS/PDC 6 9 7 2 TV PROG+/­ E+ /­ ACCESS PROGRAM CHECK SCREEN/DISPLAY Press . PR START STOP 1 8:00 10:00 2 10:00 10:45 3 11:30 13:00 4 5 6 7 8 [ ] : NEXT CH 3 2 1 DATE 24. 12 25. 12 25. 12 START+/­ D PROG 1 AT SP /L P 3 MENU OK 3 ACCESS PROGRAM SCREEN/ DISPLAY Press again to check more information. Each time you press , the next programme's information appears. ­ P1 ­ START 8:00 SP DATE 24. 12 [ SP = STOP 10:00 VPS/PDC OFF TV PROG 3 WDR ] : NEXT The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and the channel position. To cancel or replace a programme. . . 4 5 6 Press to cancel a programme. [. . . ] @ # $ % ^ & * ( ) q w e r t y u i o p Q W E ­ TV TV PROG ­ How To Use The remote control can operate most of your video recorder's functions, as well as basic functions of TV sets and satellite tuners of JVC and other brands. Point the remote control toward the sensor window. The maximum operating distance of the remote control is about 8 m. NOTES: When inserting the batteries, be sure to insert in the correct directions as indicated under the battery cover. If the remote control doesn't work properly, remove its batteries, wait a short time, replace the batteries and then try again. ATTENTION The remote control can operate not only the video recorder but also some of your TV and satellite tuner's functions. [. . . ]