User manual JVC HR-J311

[. . . ] ENGLISH CONTENTS SAFETY FIRST 2 3 4 Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 VIDEO CASSETTE RECORDER INSTALLING YOUR NEW RECORDER INITIAL SETTINGS Basic Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Auto Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Preset Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To disengage the timer, press (TIMER) again. To Timer-Record Weekly Or Daily Serials . anytime during steps 2 through 9, press WEEKLY (NUMBER key "9") for weekly serials or DAILY (NUMBER key "8") for daily serials (Monday ­ Friday). Either "WEEKLY" or "DAILY" appears on the screen. Pressing the button again makes the corresponding indication disappear. Timer Warning If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on screen to tell you that the recording is to start in 5 minutes. ­ WARNING­ TIMER RECORDING TO START SOON [] NOTE: You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes ( pg. 26). NOTES: The warning only appears if you're not in the Timer mode at that time. If this recorder is being used as the player for tape dubbing, the warning screen is recorded on the tape in the other video recorder. The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press . 26 EN TIMER RECORDING (cont. ) Check, Cancel And Replace Programmes 1 STOP+/­ 2 5 8 0 3 2 1 4 DISENGAGE TIMER MODE Press (TIMER), then press . 4 VPS/PDC 6 9 7 2 TV PROG+/­ ACCESS PROGRAM CHECK SCREEN/DISPLAY Press . PR START STOP 1 8:00 10:00 2 10:00 10:45 3 11:30 13:00 4 5 6 7 8 [ ] : NEXT CH 3 2 1 DATE 24. 12 25. 12 25. 12 START+/­ D PROG 1 ? AT E+ /­ SP /L P OK 3 MENU 3 ACCESS PROGRAM SCREEN/ DISPLAY Press again to check more information. Each time you press , the next programme's information appears. ­ P1 ­ START 8:00 SP DATE 24. 12 [ SP = STOP 10:00 VPS/PDC OFF TV PROG 3 WDR ] : NEXT The display panel shows the programme start time. Pressing OK changes the display to the programme stop time, then the date and the channel position. To cancel or replace a programme. . . 4 5 6 CANCEL OR REPLACE A PROGRAMME Press to cancel a programme. To replace a programme, press the appropriate button: START+/­, STOP+/­, DATE+/­, TV PROG+/­, VPS/PDC, SP/LP ( ) (HR-J468EU only). RETURN TO NORMAL SCREEN/ DISPLAY Press as many times as necessary. If there are still some programmes remaining, go on to step 6. RETURN TO TIMER MODE Press (TIMER). NOTE: You can also check the programmes on the display panel even if the recorder's power is off (unless the recorder is in the Power Save mode pg. 10) or the recorder is in the Timer mode; however, it is not possible to cancel or replace the programmes. EN 27 Auto SPLP Timer (HR-J468EU only) If, when timer-recording in SP mode, there is not enough tape to record the entire programme, the recorder automatically switches to LP mode to allow complete recording. Recording a programme of 210 minutes in length onto a 180minute tape Approximately 150 minutes SP mode Total 210 minutes Approximately 60 minutes LP mode Auto Timer When the Auto Timer is set to ON the timer is automatically engaged when the recorder power is turned off and automatically disengaged when the recorder is powered back on. Make sure you set "AUTO SPLP TIMER" to "ON" at the Mode Set screen before the timer-recording starts. 1 2 3 4 ACCESS MAIN MENU SCREEN Press MENU. Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #. ACCESS MODE SET SCREEN MAIN MENU MODE SET AUTO CH SET MANUAL CH SET INITIAL SET 1 2 3 4 ACCESS MAIN MENU SCREEN Press MENU. [5] = [MENU] : EXIT Press %fi to move the highlight bar (pointer) to "MODE SET", then press OK or #. ACCESS MODE SET SCREEN Press %fi to move the highlight bar (pointer) to "AUTO TIMER", then press OK or # to select either "ON" or "OFF". "AUTO SPLP TIMER" appears only with the HR-J468EU. SELECT MODE MODE SET B. ON PICTURE CONTROL AUTO AUTO TIMER OFF O. ON DIRECT REC ON AUTO SP=LP TIMER OFF POWER SAVE OFF NEXT PAGE [5] = [MENU] : EXIT Press %fi to move the highlight bar (pointer) to "AUTO SPLP TIMER", then press OK or # to select "ON". SELECT MODE MODE SET B. ON PICTURE CONTROL AUTO AUTO TIMER OFF O. ON DIRECT REC ON AUTO SP=LP TIMER ON POWER SAVE OFF NEXT PAGE [5] = [MENU] : EXIT RETURN TO NORMAL SCREEN Press MENU. RETURN TO NORMAL SCREEN Press MENU. NOTE: For safety, when Auto timer is set to "OFF", all other recorder functions are disabled while the Timer mode is engaged. To disengage the timer, press (TIMER). NOTES: If you have programmed the recorder to timer-record 2 or more programmes, the second programme and those thereafter may not fit on the tape if you set "AUTO SPLP TIMER" to "ON". [. . . ] 14, 15 +/­Button "Operating JVC TVs" below TV TV/VCR AUDIO ­ ­:­ ­ 1 4 VPS/PDC 2 5 8 AUX 3 2 6 9 4 DAILY/QTDN. WEEKLY/HEBDO 7 0000 0 START DEBUT STOP FIN DATE TV PROG EXPRESS 1 PROG ? 30 SEC MENU TV PROG + 3 OK ^ & * ( ) q w e r t y u i o p Q Buttons with a small dot on the left side of the name can also be used to operate your JVC TV while holding down the TV button. "Operating JVC TVs" below. This remote control transmits A code signals only; it is not applicable to B code signals. How To Use The remote control can operate most of your video recorder's functions, as well as basic functions of JVC TV sets. (See the right column. ) q Point the remote control toward the sensor window. [. . . ]