User manual JVC HR-J595

[. . . ] VIDEO CASSETTE RECORDER HR-J595EK PAL INSTRUCTIONS LPT0669-001B 2 safety first Safety Precautions The rating plate and the safety caution are on the rear of the unit. WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. IMPORTANT s Please read the various precautions on pages 2­4 of this instruction manual before installing or operating the recorder. s It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein. IMPORTANT Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer. [. . . ] · There will be a loss of color, or the picture will be distorted where the channel is changed. basic features 29 Notes on Recording When using both the RF and SCART cables, you can switch between TV and VCR by pressing the TV/VCR button on the Remote Control. Display Tape Position/Time Counter Press the OK button repeatedly to display the tape position and time counter on the TV screen. NOTES: · Set OSD to ON to display the indications on the TV screen. 43) · Depending on the type of tape used, the tape position may not appear right away. Change Display Information By pressing the OK button repeatedly, you can change the TV screen between the clock time and the tape position/time counter. Resetting the Counter Press the OK button so that the counter display appears on the TV screen. While the display is shown, press the 0000 button. You can reset the counter to `0:00:00' before starting playback or recording. Record a Programme While Watching Another If your VCR is connected to the TV with both the RF cable and 21-pin SCART cable, press TV/VCR. Once you have started recording all you need to do is use the controls on your TV set to tune to a different programme. The programme set using the PR button on the Remote Control is the one which will be recorded. 30 basic features Instant Timer Recording This method allows you to quickly set the VCR to record in 30 minute increments. start recording Press T (ITR) once. If left in this state, the VCR will keep recording until the tape runs out. engage instant timer recording Press T (ITR) again. This means that the VCR will record for 30 minutes on the programme already selected and then stop automatically. increase time Each time T (ITR) is pressed, the time limit is increased by 30 minutes to a maximum of 9 hours. basic features 31 VIDEO Plus +® Timer Programming before you start Make sure that the VCR's clock is set correctly Insert a cassette with the safety tab in place Turn on the TV and select the Video channel or the AV Mode Set SYSTEM to the appropriate mode. 45) ----------ONCE VIDEO PLUS+ The VIDEO Plus+ system uses the code numbers ­ called PlusCodes ­ printed after each programme in your TV listings guide. These are a kind of shorthand for video recorders and using them automatically sets your VCR to record the correct programme, channel and time. Up to 7 timer recording programmes within a month can be made. Get to the VIDEO Plus + Screen Press VIDEO Plus+. You will see the following TV screen information. Press ^& to select ONCE (once), DAILY (Monday­ Friday) or WEEKLY (weekly serials). 0~9, Enter the PlusCode Number Press the number keys on the Remote Control to enter the PlusCode number of the programme you wish to record, then press OK. The programme list appears. OK i 12345 DAILY REC VIDE PLUS+ 0~9, · If you make a mistake, press * to delete the incorrect number and then enter the correct one. · If the number you entered is invalid, PLEASE CHECK appears on the TV screen. Input a valid PlusCode number, then press OK. continued to next page 32 basic features Check the Results Make sure that the preset number displayed is the one that you want. If it is incorrect, the wrong programme will be recorded. If it is incorrect or "­ ­" is displayed, select the appropriate number using the ^ and & buttons. This preset position is registered to the VCR. change preset position Press * Tto select the PR ARD ZDF -----DATE 15 8 2 ----TIME 13 : 00~14 : 00 19 : 30~20 : 00 20 : 00~20 : 30 - - : - - ~ - -: - - - : - - ~ - -: - - - : - - ~ - -: - - - : - - ~ - -: - LP LP SP SP SP SP SP preset number. You can change the preset position using number keys or ^ and & buttons. change date Press * Tto select the date. [. . . ] 33 Tuner Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 TV Station Channel Number Guide . . . . . . . . . . . . . . . . . . . . . . . 22 TV Station ID Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 F Fine-Tuning Stored Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]