User manual JVC HR-J755

[. . . ] VIDEO CASSETTE RECORDER CONTENTS SAFETY FIRST QUICK SET UP GUIDE 2 4 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . 2 Some Do's And Don'ts . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . 5 AUTO SET UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Some satellite receiver brands have more than one code. If the satellite receiver does not function with one code, try entering another. STOP 3 TV PROG+/­ N U M R Remote A/B Code Switching The remote control is capable of controlling two JVC video recorders independently; one set to respond to the remote control's A code control signals and another set to respond to B code control signals. The remote control is preset to send A code signals because your video recorder is initially set to respond to A code signals. You can easily modify your video recorder to respond to B code signals. 2 OPERATE SATELLITE RECEIVER First, press SAT to set the remote control to satellite receiver mode, then press the corresponding button: , TV PROG +/­, NUMBER keys. For VIDEOWAY or some brands of satellite receiver, you must press after having pressed the NUMBER keys. The NUMBER buttons may not function with some satellite receivers. 1 2 3 4 REMOVE POWER SUPPLY Unplug the mains power cord from the mains outlet. IMPORTANT Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability. SET REMOTE CONTROL CODE While holding down VCR on the remote control, press the NUMBER key "2" and then press STOP. RE-SUPPLY POWER Plug the mains power cord back into the mains outlet. TURN THE RECORDER ON Press on the remote control. The recorder will now only respond to B code signals. NOTES: Some TV sets may malfunction in response to the B code. If this happens, switch back to the A code. To set the recorder back to respond to A code signals, repeat the same procedure as shown above except pressing NUMBER key "1" instead of "2" in step 2. SATELLITE RECEIVER BRAND JVC AMSTRAD GRUNDIG HIRSCHMANN SIEMENS WISI KATHREIN PACE PHILIPS FINLUX ITT NOKIA SALORA RFT SKYMASTER MASPRO BT PANASONIC JERROLD VIDEOWAY CODE 13, 14 01, 02, 03, 04 05, 06 05 05 05 05, 11, 12 06, 08 07 09 09 09 09 10 10 11 13 15 16 17 28 ADVANCED OPERATIONS (cont. ) You can use your video recorder as the source player or as the recording deck. Edit To Or From Another 1 Video Recorder . ­ ­:­ ­ MAKE CONNECTIONS Connect the player's 21-pin SCART connector to the recorder's 21-pin SCART connector as illustrated on the below. When Using Your Video Recorder As The Source Player . connect its AV1 IN/OUT connector to the recording deck. When Using Your Video Recorder As The Recording Deck . connect its AV2 IN or AV1 IN/OUT connector to the source player. 1 4 7 NUMBER "0" 2 5 8 0 3 2 6 9 4 2 TV PROG SET RECORDING DECK'S INPUT MODE Set to AUX. With this video recorder, press NUMBER key "0" and/or TV PROG to select "L-1" for the AV1 IN/ OUT connector, or "L-2" for the AV2 IN connector, depending on the connector being used. 1 3 4 START SOURCE PLAYER Engage its Play mode. START RECORDING DECK Engage its Record mode. NOTES: 3 All necessary cables can be obtained from your dealer. When you use this recorder as the player for editing, be sure to set "O. S. D. " to "OFF" before starting ( pg. If you use this recorder as the player for editing, be sure to turn off 3R Picture before starting. 17) TV Receiver Player Your recorder Recorder Your recorder TV Receiver VIDEO CHANNEL or AV mode 21-pin SCART Cable (not provided) 21-pin SCART Cable (not provided) RF Cable (provided) RF Cable (provided) Another recorder Recorder Player Another recorder VIDEO CHANNEL or AV mode 29 Edit From A Camcorder ­ ­:­ ­ You can use a camcorder as the source player and your video recorder as the recorder. 1 MAKE CONNECTIONS Connect the camcorder's AUDIO/VIDEO OUT connectors to the recorder's front panel AUDIO/VIDEO input connectors. When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder. When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling the recorder. Refer to the camcorder's instruction manual for operating procedure. 1 4 7 NUMBER "0" 2 5 8 0 3 2 6 9 4 TV PROG 1 2 3 4 SET RECORDER'S INPUT MODE Press NUMBER key "0" and/or TV PROG so that "F-1" appears in place of a preset position number. START CAMCORDER Engage its Play mode. START RECORDER Engage its Record mode. 3 NOTE: All necessary cables can be obtained from your dealer. Recorder VIDEO input AUDIO input To rear panel PAUSE connector Audio/Video Cable (not provided) VIDEO OUT Mini-Plug Cable (not provided) (JVC camcorder only) Camcorder AUDIO OUT EDIT Player 30 ADVANCED OPERATIONS (cont. ) On-Screen Display You can choose whether or not to have various operational indicators appear on screen, by setting this function ON or OFF. Other Functions Turn on the TV and select the VIDEO channel (or AV mode). 1 2 ACCESS MAIN MENU SCREEN Press MENU. ACCESS MODE SET SCREEN Move the highlight bar (pointer) to "MODE SET" by pressing %fi, then press OK or . % ­ ­:­ ­ 1 4 7 2 5 8 0 3 2 6 9 4 3 OK ENABLE/DISABLE ON-SCREEN DISPLAY The default setting is "ON", so if you want onscreen displays, leave the setting as it is and go to step 4. If you don't want the displays to appear, press %fi to move the highlight bar (pointer) to "O. S. D. " and press OK or to set "O. S. D. " to "OFF". [. . . ] 28 r Button engages timer-standby mode. 13, 15 t DATE +/­ Button inputs date of programme for timer recording. 14 y TV PROG +/­ Button -- same as button on recorder. 10 u 30 SEC Button initiates a 30-second period of fast-motion playback. [. . . ]