User manual JVC HR-S9600

[. . . ] CONTENTS SAFETY FIRST 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Some Do's And Don'ts . . . . . . . . . . . . . . . . . . . . . 4 VIDEO CASSETTE RECORDER QUICK SET UP GUIDE 5 HR-S9600EK CHECK THE CONTENTS . . . . . . . . . . . . . . . . . . 5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press and hold PAUSE and press RECORD on your recorder so that the recorder enters the RecordPause Mode. 1 2 1 4 7 NUMBER "0" 1 2 2 5 8 0 PA ­ ­:­ ­ 3 6 9 3 4 4 3 START SYNCHRO EDITING Press SYNCHRO EDIT. PAUSE SYNCHRO EDITING Press SYNCHRO EDIT again. Repeat steps 4 ­ 6 as necessary. TV PROG Recorder NOTES: SYNCHRO EDIT connector The Synchro Edit function may not work with the initial part of a camcorder tape. The Synchro Edit function cannot be used when using the JLIP function. (Pressing SYNCHRO EDIT cancels the JLIP function. ) The Synchro Editing function may not work properly with some type of camcorder. When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B. E. S. T. is set to OFF) after you finish dubbing the tapes. LANC Cable (not provided) Player Camcorder To LANC connector 38 ADVANCED OPERATIONS (cont. ) You can use your video recorder as the source player or as the recording deck. Edit To Or From Another 1 Video Recorder MAKE CONNECTIONS Connect the player's 21-pin SCART connector to the recorder's 21-pin SCART connector as illustrated on page 39. A When Using Your Video Recorder As The Source Player . . . connect its AV1 IN/OUT connector to the recording deck. B When Using Your Video Recorder As The Recording Deck . . . connect its AV2 IN/DECODER or AV1 IN/OUT connector to the source player. C If Another Recorder Is Compatible With The Y/C Signal . . . connect your recorder's AV1 IN/OUT connector to another recorder. When using your recorder as the recording deck, set "AV1 SELECT" to "S-VIDEO" and "AV2 SELECT" to "AV2" ( pg. When using your recorder as the source player, set the AV1 OUT switch on the rear panel to Y/C ( pg. 6). 1 2 ­ ­:­ ­ 1 4 7 NUMBER "0" 1 2 2 5 8 0 3 6 9 3 4 4 3 2 TV PROG SET RECORDING DECK'S INPUT MODE Set to AUX. With this video recorder, press NUMBER key "0" and/or TV PROG to select "L-1" for the AV1 IN/ OUT connector, or "L-2" for the AV2 IN/DECODER connector, depending on the connector being used. When using the AV2 IN/DECODER connector, set "AV2 SELECT" to the appropriate mode. 40) 3 4 5 SET EDIT MODE See "Picture Control" on page 35. START SOURCE PLAYER Engage its Play mode. START RECORDING DECK Engage its Record mode. 39 A TV Receiver Player Your recorder B Recorder Your recorder TV Receiver VIDEO CHANNEL or AV mode 21-pin SCART Cable (not provided) RF Cable (provided) 21-pin SCART Cable (not provided) RF Cable (provided) VIDEO CHANNEL or AV mode Another recorder Recorder C TV Receiver Recorder Your recorder Player Another recorder S-Video Cable (provided) 21-pin SCART Cable (not provided) Another recorder Player NOTES: All necessary cables can be obtained from your dealer. For Y/C signal input/output, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal. When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B. E. S. T. is set to OFF) after you finish dubbing the tapes. When you use this recorder as the player for editing, be sure to set "O. S. D. " to "OFF" before starting ( pg. [. . . ] 14 o OK Button -- same as button on recorder. 21 Q TV PROG +/­ Button -- same as button on recorder. 14 W DATE +/­ Button -- same as button on recorder. 18 E Fast Forward [FF] Button -- same as button on recorder. [. . . ]