User manual JVC HR-S9800

[. . . ] VIDEO CASSETTE RECORDER HR-S9800U VCR TV CABLE/DBS A. MONITOR POWER A/B TV/VCR DISPLAY ENTER/OSD . , ? 1 ABC 2 DEF 3 2 4 DHI DBS PQRS 5 JKL DAILY(M-F) TUV MNO 6 9 WEEKLY WXYZ 7 8 0 C. RESET CANCEL AUX TIMER 4 START STOP DATE CH EXPRESS PROGRAMMING 1 PROG SP/EP PROG CHECK SKIP SEARCH PLAY REW FF STOP REC TV CH + PAUS E TV VOL TV VOL + ME NU 3 TV CH OK NAVIGAT ION JOG/ SHUTTLE INSTRUCTIONS For Customer Use: Enter below the Model No. which are located on the rear of cabinet. Retain this information for future reference. [. . . ] (The PlusCode programing numbers are the numbers next to the program in most TV listing. ) 1 Load a cassette Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load it into the VCR. The VCR turns on, and the counter is reset, automatically. 1 2 Access VCR Plus+ screen VCR PLUS+ Press PROG. The clock must be set to access the VCR PRESS NUMBER KEY (09) Plus+ screen. PRESS (+/) TO SET EXPRESS PROGRAMMING If you have not set the PRESS (PROG. ) TO END clock, the Main Menu screen appears after an error message is displayed. Refer to page 8 for the Plug & Play setting or page 10 for the clock setting procedure. VCR TV CABLE/DBS POWER 1 4 2 5 8 0 3 6 9 34 WEEKLY DAILY (M-F) CANCEL STOP +/ 7 27 4 8 4 6 3 Enter PlusCode number Press the appropriate Number keys to input the PlusCode number printed in the TV listings for the TV broadcast you wish to record, then press OK. VCR PLUS+ 123 PRESS NUMBER KEY (09) THEN (OK) PRESS (PROG. ) TO END 347 Then; If the Guide Channel Set screen appears -- go to step 4. If the VCR Plus+ Program screen appears -- go to step 5. To make corrections, press CANCEL and input the correct PlusCode number. EN 39 4 Input receiving channel number The guide channel GUIDE CHANNEL SET number, which is GUIDE CH: 12 assigned to the TV or VCR CH : cable station for the PlusCode number that PRESS NUMBER KEY (09) you entered in step 3, OR (5, ), THEN (OK) PRESS (PROG. ) TO END will appear automatically on the Guide Channel Set screen. Press the Number keys (or CH +/ or %fi) to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press OK. The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously. If you receive your channels with a cable box and if you have properly set your Controller, "CABLE CH" appears in place of "VCR CH". If not, refer to pages 16 19. 7 Return to normal screen Press PROG. "PROGRAM COMPLETED" appears on the screen for about 5 seconds, then normal screen appears. If "PROGRAM NOT COMPLETED PROGRAM OVERLAP" appears, you have another program overlapping the program you have just made. The Program Check screen appears and conflicting programs will start blinking. You can now correct the conflicting programs. See "When programs overlap each other" on page 45. 8 Engage timer recording standby mode Press TIMER. The VCR turns off automatically and "" is displayed on the front display panel. To use the VCR while it is in timer recording standby mode Press TIMER to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER after you use the VCR; otherwise, you cannot record the broadcasts you want. 57) is set to "ON", the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER to engage or disengage the timer recording standby mode. 5 Check program date The PlusCode number you entered and the corresponding timer recording program is displayed on the Program screen. [. . . ] All products and parts thereof may be brought to a JVC authorized service center on a carry-in basis except for Television sets having a screen size 25 inches and above which are covered on an in-home basis. WHAT YOU MUST DO FOR WARRANTY SERVICE: Return your product to a JVC authorized service center with a copy of your bill of sale. For your nearest JVC authorized service center, please call toll free: (800) 252-5722. If service is not available locally, box the product carefully, preferably in the original carton, and ship, insured, with a copy of your bill of sale plus a letter of explanation of the problem to the nearest JVC Factory Service Center, the name and location of which will be given to you by the toll-free number. [. . . ]