User manual JVC HR-XVC15UC-HR-XVC15 Instruction Manual

[. . . ] DVD/CD PLAYER Hi-Fi STEREO VIDEO CASSETTE RECORDER USER'S GUIDE For model: HR-XVC15U For Customer Use: Enter below the Model No. which are located on the rear of cabinet. Retain this information for future reference. Model No. Serial No. LPT0787-001A *J2C31501A* CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Make sure TV/VCR/DVD switch has been slided to VCR/DVD. (The VCR indicator will light. ) Example: Instant Timer Recording for 30 minutes. 1 Load a cassette tape with the erase prevention tab intact. The VCR will automatically turn on. to 2 Press SP/EPEP. select the desired tape speed SP or The tape counter and "SP" or "EP" will appear on the screen for about 4 seconds. 00 : 00 : 00 SP 3 Set the TV/CATV option to the appropriate position (see page 19). TV - VHF/UHF channels CATV - CABLE TV channels 4 Press Number keys or VCR CH +/ to select the channel to be recorded. CH 110 Press REC the VCR or while holding REC, press PLAY on 5 the Remote on begin recording. Press REC on the VCR again to to stop recording after 30 minutes. Each additional press of REC will increase recording time as shown in the chart below, up to a maximum of 6 hours. The ITR and recording time will appear on the screen for about 4 seconds. And, REC will keep blinking in the display. Press Recording time NORMAL REC once twice 0:30 3 times 1:00 4 times 1:30 5 times 2:00 Press Recording time 3:00 6 times 4:00 7 times 5:00 8 times 6:00 9 times 10 times NORMAL REC ITR 0 : 30 CH 110 INDEX NOTE: If you wish to watch the DVD playback during the ITR, press DVD to change to DVD mode and perform the DVD playback (see page 37). To cancel ITR Press STOP or turn off the power. " " will appear on screen for about 4 seconds. 30 Timer recording Timer recording can be programmed on-screen with the remote control. The built-in timer allows automatic unattended recording of up to 8 programs within 1 month. Preparation: Make sure TV/VCR/DVD switch has been slided to VCR/DVD. Load a cassette tape with the erase prevention tab intact. Press OSD to verify time and date are correct (see page 29). Example: Program a timer recording for the 26th day, channel 125 (CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: EP). 1 Press SET UP MENU. Select the TIMER REC SET option, then press ENTER. select one of 2 Press SET + or topress ENTER. the program line, then MENU TIMER REC SET AUTO REPEAT ON OFF ON OFF SAP CH SETUP SYSTEM SETUP +//ENTER/MENU DATE START END : : : : : : : : : : : : : : : : CH +//ENTER/CANCEL/MENU SET + or to 3 Presspress ENTER. select the date, then DATE START END CH 26(SU) : : : : : : : : : : : : : : : : +//ENTER/CANCEL/MENU time, 4 Set the start time, endstep 3. channel and tape speed as in NOTES: NOTES: If the clock symbol ( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape supply. In this case, press TIMER to cancel the timer program or press EJECT to remove the cassette tape. During timer recording standby mode, the VCR mode cannot be selected. To use the VCR, press TIMER at first, then press VCR to change to VCR mode. After you use the VCR, press TIMER again to put the VCR into timer recording standby mode. If you press TIMER during timer recording, the recording operation will be interrupted. [. . . ] Damage that occurs in shipment, due to act of God, and cosmetic damage; 5. Signal reception problems and failures due to line power surge; 6. Video Pick-up Tubes/CCD Image Sensor, Cartridge, Stylus (Needle) are covered for 90 days from the date of purchase; 7. Batteries (except that Rechargeable Batteries are covered for 90 days from the date of purchase); There are no other express warranties except as listed above. [. . . ]