User manual JVC KA-DV300U-KA-DV300 Instruction Manual

[. . . ] Safety Precautions Thank you for purchasing this product. (These instrustions are for KA-DV300U) Before beginning to operate this unit, please read the instruction manual carefully in order to make sure that the best possible performance is obtained. English Due to design modifications, data given in this instruction book are subject to possible change without prior notice. NETWORK PACK STARTUP GUIDE Deutsch NETZWERKPACK BEDIENUNGSLEITFADEN BACK DE RESEAU GUIDE DE DEMARRAGE WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. AVERTISSEMENT: POUR EVITER LES RISQUES D'INCENDIE OU D'ELECTRO-CUTION, NE PAS EXPOSER L'APPAREIL A L'HUMIDITE OU A LA PLUIE. POWER SYSTEM KA-DV300 INSTRUCTIONS BEDIENUNGSANLEITUNG MANUEL D'INSTRUCTIONS Français Connection of POWER supply The power for the network pack is supplied through the camera that is connected to the network pack. This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. [. . . ] To resume transmission or recording, press the REC START/STOP button once more. 6. 8. To stop transmission, press the SELECT dial. To resume transmission, press the SELECT dial once more. To end, press the SELECT dial to stop transmission and turn off the power. Lastly, remove the LAN card. ENCODE SET menu screen Set to SPLIT 8. 9. Memo When using the SELECT dial for GAIN or SHUTTER operation, no operation on the SELECT dial will be accepted for about 3 seconds after the operation is completed. Recording will not be made on the DV cassette tape even if a tape is inserted. To end, press the REC START/STOP button to stop transmission and recording and turn off the power. Lastly, remove the LAN card. Memo Streaming data will be sent from the LAN card even when a DV cassette tape is not inserted. When the DV cassette tape reaches the end during recording, the transmission of streaming data from the LAN card is also stopped. 26 27 LAN card Sending playback signals of a DV cassette tape using a LAN card NETWORK PACK SETUP With the Network Pack, GY-DV300/KA-DV300 can be controlled via LAN. Controlling GY-DU300/KA-DU300 via a LAN card POWER switch MODE switch MENU button BAR It is also possible to playback video and audio from KA-DV300 on your PC in the STREAMCAPTURE screen in realtime (live display) as POWER OFF MODE CAM-B ON well as save data to files. However, note that video and audio from KA-DV300 can be played back only on one PC at a time. Peer-to-peer connection that directly connects the unit with a PC is explained here. CAM-A GAIN VTR SHUTTER GY-DV300 SELECT Tdial AUDIO LEVEL ND FILTER ON OFF IRIS PC MENU AW FWD CH-1 CH-2 PROFESSINAL Set the LAN card driver by following the instructions on manual provided by the card manufacturer. REV FOCUS AUTO MANU DV CAMCORDER GY-DV300 PUSH AUTO 10 BASE-T cross cable <GY-DV300 rear panel> KA-DV300 LCD screen Socket Com: EA2900-117 (USA) EA2903-162 (Europe) EA2906-194 (Asia) (CF memory card adapter (PCMCIA TYPE I/II specifications)(sold separately) is required for inserting this card. ) 1. 2. e Insert a LAN card into the Network Pack. Check to see that the LAN card display is showing on the LCD screen/viewfinder screen. LAN card display No LAN card is inserted when the display 3. 5. Set the MODE switch to "VTR". Set the NETWORK PACK CONFIG menu screen. w Set the video/audio compression in the ENCODE SET menu screen. ( page 6) e When completed with settings, press the MENU button to return to the normal screen. Launch Streamproducer. * Press the BAR (t/w) button of GY-DV300 to start DV cassette tape playback. Press the SELECT dial at the beginning of the scene to send from LAN card. The LAN card display on the LCD screen/viewfinder screen will be as follows: e : Yellow display during data transmission. Displayed in red when the media operating Streamproducer* at the destination of transmission starts recording. * Perform setting described in "5-2 Operating video from DV camcorder · Trigger mode function" of network distribution software "Streamproducer" User's Guide. 1. [. . . ] Place metal articles that may be blocking the transmission away from the camera and your PC when using wireless LAN. Make sure the LAN cables are not severed if you use cables. Make sure the LAN card is inserted correctly in the NETWORK PACK. The status of operation is shown on each video display window if you check in this box before your operation. Take the check mark off if you want to hide the Status Bar. Unable to receive casting image. Send Ping command to the IP address of Streamproducer. [. . . ]