User manual JVC KA-DV350U

[. . . ] NETWORK PACK KA-DV350U User's Guide LST0196-001A Thank you for purchasing this NETWORK PACK KA-DV350U. Notes on usage Caution Items concerning the operations of this product are described. References concerning the usage, restrictions, etc. Reference pages and reference items are indicated. Memo Proprietary terms All rights reserved by JVC. Unauthorized duplication or reprinting of this manual, in whole or in part, is strictly prohibited. [. . . ] secured Launch the browser on your PC and enter 192. 168. 100. 101 (default factory setting) in the address bar and press ENTER. · A confirmation window for user ID and password appears. · For the user ID, input "jvc" (factory setting). For the password, input "ka-dv300" (factory setting) or the name set in the SERVER SETUP menu screen. ( page 17) · Check to make sure the inputted user ID and password are correct and click the OK icon. (Check "Save password" so that the password does not need to be inputted for future accesses. ) If the user ID and password are correct, the Streamcorder screen appears on the PC monitor. ? OK X Cancel 3. Memo · Users referred as "jvc" (can be changed) that can perform all operations, "ENCODE" users that can view all data but only change the encoding settings, and "BROWSE" users that can only view data. · The default password for each user type is "ka-dv300" for "jvc" users, first 4 characters of the password set for "jvc" users for "ENCODE" users (default is "ka-d") and fixed password of "ka-dv" for "BROWSER" users. · When changing the password, "ENCODE" users will be fixed with the first 4 characters of the set password and "BROWSE" users will be fixed with "ka-dv" as the password. · The following is an explanation when login is made a user permitted with all operations. In the case of other users, the OK button and Cancel button will be disabled even if operations on the screen are allowed. · Depending on the cache setting of your browser, the parameters updated in the Camera menu may not be effective immediately. 44 OTHERS OPERATION PREPARATION INTRODUCTION Using the CF (Compact Flash) Card Inserting Inserting the card Caution · Make sure the power of GYDV300 is off when inserting/ removing a CF card. Inserting/ removing a card with the unit power on may damage the data storage section of the CF card itself. · Do not remove the power cable with the power of the GY-DV300 on. Recorded section on the CF card or the CF card itself may be damaged as a result. Card slot CF Card adapter CF Card KA-DV350 EJECT button ACCESS lamp LCD screen CF 1. Insert a card into the KA-DV350 card slot. Card status according to the inserted card type is displayed on the LCD screen/viewfinder screen. ( page 8) Card status display : No card Memo e : LAN card C F : CF card Removing Memo When turning the power on, the card status display shown on left will flash during initialization. · Check to make sure the ACCESS lamp of KA-DV350 is off. · The ACCESS lamp will light when the card is in operation. 1. 2. Memo Turn off the GY-DV300 power. Press the EJECT button of KA-DV350 and remove the card. Remember that when the CF card to be used is in the following conditions, normal recording and playback cannot be made. · When the card is not yet formatted · When the card is formatted by systems other than the Windows system · When formatting cannot be recognized by the KA-DV350 * Under such circumstances, there can be a case where an error message of "NO CLIP!" appears on the liquid crystal display surface of the GY-DV300 or a case where nothing appears on it. 45 OTHERS OPERATION PREPARATION INTRODUCTION Using the CF (Compact Flash) Card · Executing DELETE ALL · Recording to the CF card Formatting the card If the CF card is unformatted when performing any of the operations shown below, "NO CF FORMAT" will appear in the LCD screen/viewfinder screen. Memo · If the unit enters MOVIE CLIP by operating the menu or the REC START/STOP button during formatting CF card, a display of the LCD viewer can go wrong. However, if you operate the menu after formatting has been completed, you will be able to regain a normal display. POWER OFF ON MENU button BAR MODE CAM-B CAM-A GAIN VTR SHUTTER MENU AW FWD SELECT dial REV <GY-DV300 rear panel> NO CF FORMAT! CF 1. [. . . ] 128bit WEP: Encryption is performed using 104-bit + 24-bit (1V) keys. Although throughput will decline compared to Open System, security of data will be improved. Gateway Hardware and software that translates different types of protocols when a computer communicates with another computer outside the network. The gateway IP address is referred to as the gateway address. RTP (Realtime Transport Protocol) Protocol to transmit in realtime digitalized video/ audio data via a network. RTSP (Real Time Streaming Protocol) Protocol to control realtime transmission of video/audio data via a network. HTTP (Hypertext Transport Protocol) Protocol used when transferring HTML (Hypertext Markup Language) files between WWW server and web browser. Access point (wireless LAN) Relay point for infrastructure communication. It can also serve as the relay point for cable LAN or wireless LAN. Protocol A set rule for a computer or communication device to perform communication over a network, etc. ASF (Advanced Streaming Format) Data streaming format developed by Microsoft Corporation (U. S. ) for transmission of video and audio. IEEE802, 11b International standard for wireless LAN with maximum communication speed of 11Mbps. Host name Name of a device (not limited to a computer but all connection devices with an IP address) on a network. 79 Glossary IP address Identification number assigned to each computer that is connected to a network. [. . . ]