User manual JVC KA-F5603U

[. . . ] KA-F5602U KA-F5603U INSTRUCTIONS ft m 16 11 8 10 45 1. 2 1. 5 7 2 10 3 15 30 5 10 F. f MACRO 5. 5 C BREAKER PROMPTER OUTPUT RM DC INPUT *Illustration with optional lens and viewfinder attachments. Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance. For Customer Use: Enter below the Serial No. Retain this information for future reference. KA-F5602U/KA-F5603U Serial No. LWT0176-001D Japanese STUDIO KIT STUDIO SDI KIT English 1. [. . . ] This is to be inserted into the slot at the rear of KY-F560. [SDI OUT] SDI Output Terminal. . . Only for KA-F5603U Camera video is output in the form of SDI signal. 0 Caution To avoid causing malfunction, please do not touch this terminal except when connecting cable to it. 6 ! [VF] Viewfinder Terminal (6 Pin) Use for connecting cable from the Viewfinder. Viewfinder Holder Use for mounting the VF-P400 4-inch Viewfinder. Lens Cable Clamp This clamp is meant for securing the lens cable. @ # 7 8 11 English Getting Started Part Names and Functions (continued) BREAKER PROMPTER OUTPUT RM DC INPUT ^ $ % & $ [PROMPTER OUTPUT] Prompter Output Terminal (BNC) Signal (prompter video signal) inputted into the [AUX] input terminal of the remote control unit will be outputted from this terminal via the RM multi-pin connector. [DC INPUT] DC Power Input Terminal (XLR 4 Pin) Apply DC power to this terminal if Remote Control Unit RM-P210 is not going to be connected. For DC power supply, use AAP250. ^ % [BREAKER] Breaker Switch Breaker switch will trip and cut off the power if the power consumed is higher than the rated capacity. If the breaker switch trips, confirm that there are no abnormalities and that the power consumption does not exceed the rated wattage. If no abnormalities are detected, press the breaker switch before turning the power ON again to put this unit in the operating status. If this unit still does not function properly, consult your JVC-authorized dealer. Screw Holes for Mounting Tripod & 12 Installation System Viewfinder VF-P400 AC power adapter AA-P250 VC-710 (5 m) Studio kit/Studio SDI kit KA-F5602U/KA-F5603U Lens MACRO 4P Color video camera KY-F560 Headset KA-310U COLOR VIDEO CAMERA KY-F560 BREAKER PROMPTER OUTPUT RM DC INPUT [PROMPTER OUTPUT] connector SDI output (only KA-F5603U) [INTERCOM] connector [DC INPUT] connector SDI input RM multi-pin connector SDI compatible video equipment 26Pin camera cable VC-P110 (5 m) VC-P112 (20 m) VC-P113 (50 m) VC-P114 (100 m) REMOTE CONTROL UNIT RM-P210 Monitor Headset KA-310U Tripod TP-P300 TALLY CALL FULL AUTO F1 SHUTTER F3 MENU/SHUTTER GAIN STEP HIGH PAINT WHITE AUTO W. BAL B MASTER BLACK IRIS POWER I SHUTTER BARS F2 GAIN INTERCOM LEVEL DOWN UP VARIABLE PUSH-ON LOW MID A F4 MENU PUSH-ON R B PRESET AUTO MANU O DOWN UP CLOSE OPEN Remote control unit RM-P210 Dolly TP-P205 Please refer to KY-F560 instruction manual for details on the lens and lens remote control. The 26 Pin camera cable used should be less than 100 m. Power is supplied via the 26 Pin camera cable by the Remote Control Unit RM-P210 if it is in-use. If the Remote Control Unit RM-P210 is not in-use, please use AC power adapter AA-P250. 13 English 4P Installation Installation Procedures 1. Mounting KY-F560 Camera on this Unit. 2. Mounting the Lens onto the Camera. 3. Mounting this Unit onto the Tripod. 4. Mounting VF-P400 4-inch Viewfinder on this Unit. Mounting KY-F560 Camera on this Unit 1. Screw Å 1. Slot cover Preparations to be done on KY-F560 camera. If the lens is attached to KY-F560 camera, remove and place it aside. Attached the camera mounting bracket at the bottom of the camera. Remove 2 screws Å from the rear of the camera and take out the slot cover. Camera mounting bracket 2. 2. Loosen 2 screws i of this unit and pull out the camera mounting frame. Screw i Camera mounting frame 14 Mounting KY-F560 Camera on this Unit (continued) 3. 3. Mounting bracket 4. Screw Ç After the camera mounting frame is inserted into this unit, secure it by screwing back the 2 screws i which were taken out earlier in above-mentioned step 2. . 4. Camera mounting frame Notes Please remove the camera lens mount cap before hand. [. . . ] 4. REMOTE CONTROL UNIT RM-P210 TALLY CALL FULL AUTO F1 SHUTTER SHUTTER BARS F2 GAIN INTERCOM LEVEL DOWN UP DOWN UP CLOSE OPEN F3 MENU/SHUTTER GAIN STEP HIGH PAINT WHITE AUTO W. BAL B MASTER BLACK IRIS POWER MENU AW BARS SET I A VARIABLE PUSH-ON LOW MID F4 MENU PUSH-ON R B PRESET AUTO MANU REMOTE LENS O GENLOCK IN VIDEO OUT DC IN POWER SEE INST INCOM MIC ON CARBON VF INTERCOM OFF DYNAMIC INCOM LEVEL PUSH CALL MIN MAX ft m 16 11 8 10 45 1. 2 1. 5 7 2 10 3 15 30 5 10 F. f MACRO 5. 5 C BREAKER PROMPTER OUTPUT RM 38 GENLOCK IN VIDEO OUT DC IN POWER SEE INST INCOM MIC ON CARBON VF INTERCOM OFF DYNAMIC INCOM LEVEL PUSH CALL MIN MAX GENLOCK IN VIDEO OUT DC IN POWER SEE INST INCOM MIC ON CARBON VF INTERCOM OFF DYNAMIC INCOM LEVEL PUSH CALL MIN MAX 39  Japanese 40 41 Japanese 42 · · · · 43 Japanese 146. 6 16. 5 25 95 INCOM MIC ON CARBON VF 180. 3 57. 5 INTERCOM OFF DYNAMIC INCOM LEVEL PUSH CALL MIN MAX 160 185. 1 204. 3 156 44 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]