User manual JVC KD-LX30R

[. . . ] CD RECEIVER CD-RECEIVER RECEPTEUR CD CD-RECEIVER KD-LX30R SCM SEL 7 MONO 8 LOCAL 9 MODE BAND S S M DISP ATT SOURCE TP RDS PTY INT 10 RPT 11 RND 12 OFF KD-LX30R For installation and connections, refer to the separate manual. Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung. Pour l'installation et les raccordements, se référer au manuel séparé. Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het toestel. [. . . ] · If you do not want to store the sound mode separately for each playback source, but want to use the same sound mode for all the sources, see "To cancel Advanced SCM" on page 34. "Link" indicator 2 1 1 2 Within 5 seconds Light "MODE" on the lower part of the display. The number buttons can work as different function buttons. Select the sound mode you want. Each time you press the button, the sound mode changes as follows: BEAT SOFT POP OFF · If the "Link" indicator is lit on the display (with "SCM LINK" set to "SCM LINK ON" -- see page 34), the selected sound mode can be stored in memory for the current source, and the effect applies to the current source. · If the "Link" indicator is NOT lit on the display (with "SCM LINK" set to "SCM LINK OFF"), the selected sound mode effect applies to any source. Indication OFF BEAT SOFT POP 26 For: Bass (Flat sound) Rock or disco music Quiet background music Light music 00 +02 +01 +04 Preset values Treble 00 00 ­03 +01 BBEII BBE 2 BBE 2 Off Off SOURCE (ATT) Select the source while the "Link" indicator is lit on the display. The "Link" indicator starts flashing, and the sound mode stored in memory for the selected source is recalled (and appears on the display for a while). Notes: · You can adjust each sound mode to your preference, and store it in memory. If you want to adjust and store your original sound mode, see "Storing your own sound adjustments" on page 28. · To adjust the bass and treble reinforcement levels or to turn on/off the BBEII function temporarily, see pages 24 and 25. (Your adjustments will be canceled if another source is selected. ) · By setting "CLOCK DISP" to "CLK DISP OFF" (see page 34), you can always show the current sound mode setting when the unit is turned on. 27 ENGLISH Recalling the sound modes ENGLISH Storing your own sound adjustments You can adjust the sound modes (BEAT, SOFT, POP: see page 26) to your preference and store your own adjustments in memory. 4 3 2, 5 1 1 Light "MODE" on the lower part of the display. The number buttons can work as different function buttons. REMEMBER you must finish the following steps while "MODE" is still on the display. Otherwise, the setting will be canceled. 2 3 4 Select the sound mode you want. For details, see page 26. Select the item you want to adjust (BAS, TRE, or BBEII). Adjust the selected item. 5 Press and hold SCM until the sound mode you have selected flashes on the display. Your adjustment made for the selected sound mode is stored in memory. 6 Repeat the same procedure to adjust other sound modes. To reset to the factory settings Repeat the same procedure and reassign the preset values listed in the table on page 26. 28 OTHER MAIN FUNCTIONS You can also set the clock system either 24 hours or 12 hours. 1, 5 2, 3, 4 2, 3, 4 1 2 Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears on the display. 1 Select "CLOCK HOUR" if not shown on the display. 2 Adjust the hour. 3 1 2 Set the minute. 1 Select "CLOCK MINUTE. " 2 Adjust the minute. 4 1 2 Set the clock system. 1 Select "CLOCK24H/12H. " 2 Select "CLOCK 24HOUR" or "CLOCK 12HOUR. " 5 Finish the setting. To check the current clock time while the unit is turned off, press + or ­. The power turns on, the clock time is shown for 5 seconds, then the power turns off. 29 ENGLISH Setting the clock ENGLISH Controlling the volume automatically (Audio Cruise) You can select the proper cruise mode for your car. This unit changes the volume level automatically (at 3 possible levels) based on the driving speed of your car by detecting the alternator's generating frequency (Audio Cruise). If you want to use this mode, follow the procedure below. When shipped from the factory, this mode is set to "CRUISE OFF. " · CRUISE 1: Select this if your car is relatively quiet. · CRUISE 2: Select this if your car is relatively loud. The volume increase rate is twice as much as that of the CRUISE 1 setting. · CRUISE OFF: Cancels Audio Cruise. 1, 4 3 2 1 Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears on the display. 2 Select "CRUISE MODE. " 3 Select the desired setting. Each time you press the button, the Audio Cruise mode changes as follows: CRUISE 1 CRUISE 2 CRUISE OFF 4 Finish the setting. 30 When the driving speed increases. When the driving speed decreases. To adjust the volume increase rate If you find Audio Cruise increases (or decreases) the volume either too much or too little as the driving speed changes, you can adjust the increase rate by changing the boost level. [. . . ] We recommend that you stop CD play while driving on such rough roads. 55 ENGLISH Handling CDs TROUBLESHOOTING ENGLISH What appears to be trouble is not always serious. Check the following points before calling a service centre. Symptoms · CD cannot be played back. · CD sound is sometimes interrupted. Causes CD is inserted upside down. [. . . ]