User manual JVC KD-LX50

[. . . ] CD RECEIVER CD-RECEIVER RECEPTEUR CD CD-RECEIVER KD-LX50R VCR SEL /I 7 MONO 8 LOCAL 9 SCM MODE S S M DISP ATT SOURCE BBE BAND INT 10 RPT 11 RND 12 OFF KD-LX50R For installation and connections, refer to the separate manual. Angaben zu Einbau und Verkabelung entnehmen Sie bitte der gesonderten Anleitung. Pour l'installation et les raccordements, se référer au manuel séparé. Zie de afzonderlijke handleiding voor details aangaande het installeren en verbinden van het toestel. [. . . ] In this case, speak the word(s) again. TO BE CONTINUED ON THE NEXT PAGE 35 ENGLISH 6 STOP PLAY ENGLISH 9 Speak the same word(s) again while "REPEAT" is flashing on the display. (In this example, speak "Turn off. ") "CHECK" appears on the display while recording your voice. "OK" appears when recording is complete. " " on the display means that your own voice is recorded for this voice command. If the recording fails A beep sound comes out and the display goes back to the one shown in step 6. 10 11 Repeat steps 6 to 9 to record your own voice for other preset Operation Commands (VOICE 02 to VOICE 13). Press and hold VOICE again to finish the recording. To erase your own voice from the Operation Commands See "To erase the voice commands" on page 45. 36 STOP PLAY You can store the frequently-used operations into the Access Commands and register your voice to make the System execute the Access Commands. · You can store the following operations into the Access Commands; ­ Selecting CD or External component as the source. (FM and AM) ­ Selecting the band and preset number. (DAB) ­ Selecting the CDs in the CD changer. · Set "VOICE DEMO" to "DEMO OFF. " Without setting it to "DEMO OFF, " you cannot preset the Access Commands. · Notice the following; ­ You can store up to 12 Access Commands (12 operations and voice commands into memory). ­ Each voice command must be within 3 second long. ­ You can register any word you want; however, if it is too short (ex: "Pops"), the System may not recognize it correctly. Registering procedure (for the first Access Command) EXAMPLE: Storing an operation of "selecting the FM station of 89. 5 MHz, " and registering words "Jazz 89" as your Access Command to that operation into Access Command number 14. 3, 7 1- 1, - 4 1- 3 1- 2 4 Voice remote 1 Select the User Word mode by following steps 1 to 4 on page 34. 1 Press and hold SEL (Select) for more than 2 seconds so that one of the PSM items appears on the display. 2 Press ¢ or 4 repeatedly until "VOICE DEMO" appears on the display. 3 Press ­ to select "DEMO OFF. " 4 Press SEL again to finish the setting. TO BE CONTINUED ON THE NEXT PAGE 37 ENGLISH Presetting the Access Commands STOP PLAY ENGLISH 2 Select the operation you want to store into the Access Command. (In this case, select "FM 89. 5 MHz. ") If you want to memorize the sound mode at the same time Select the sound mode you want. (See page 27. ) Notes: · Preset number (FM and AM) cannot be stored but only its station frequency is stored into the Access Command. · To store a DAB service into the Access Command, select a preset DAB service. (See pages 72 to 74. ) 3 Press and hold VOICE until Access Command (VOICE 14) appears on the display. 4 Press STR (ATT) to make the System ready to record your voice. "SPEAK" starts flashing on the display after the voice navigation "Please speak now. " 5 Speak the word(s) you want to record while "SPEAK" is flashing on the display. (In this example, speak "Jazz 89. ") · If the System recognizes your word(s), "REPEAT" starts flashing on the display after the voice navigation "Please repeat. " · If the System does not recognize your word(s), it will ask you to speak again. 38 STOP PLAY Speak the same word(s) again while "REPEAT" is flashing on the display. (In this example, speak "Jazz 89. ") "CHECK" appears on the display while recording your voice, "OK" appears when recording is complete. 7 Press and hold VOICE again to finish the recording. TO BE CONTINUED ON THE NEXT PAGE 39 ENGLISH 6 STOP PLAY ENGLISH Registering procedure (Continued for the second Access Command by following the previous one) EXAMPLE: Storing an operation of "selecting disc number 01 in the CD changer, " and registering word "Classics" as your Access Command to that operation into Access Command number 15. 2, 6 3 Voice remote 1 Select the operation you want to store into the Access Command. (In this case, select "disc number 01 in the CD changer. ") 2 Press and hold VOICE until Access Command (VOICE 15) appears on the display. 3 Press STR (ATT) to make the System ready to record your voice. "SPEAK" starts flashing on the display after the voice navigation "Please speak now. " 40 STOP PLAY Speak the word(s) you want to record while "SPEAK" is flashing on the display. (In this example, speak "Classics. ") · If the System recognizes your word(s), "REPEAT" starts flashing on the display after the voice navigation "Please repeat. " · If the System does not recognize your word(s), it will ask you to speak again. In this case, speak the word(s) again. 5 Speak the same word(s) again while "REPEAT" is flashing on the display. [. . . ] Store stations manually. · Sound cannot be heard from the speakers. The volume level is set to the minimum level. Connections are incorrect. · SSM (Strong-station Sequential Memory) automatic preset does not work. · Static noise while listening to the radio. · "NO DISC" appears on the display. [. . . ]