User manual JVC KD-SC607 INSTALLATION MANUAL

[. . . ] The number in parentheses indicates the quantity of the pieces supplied. After checking them, please set them correctly. . , , . A/B Hard case/Control panel (1) / (1) C Sleeve (1) (1) D Trim plate (1) (1) E Power cord (1) (1) F Washer--ø5 (1) --5 (1) G Lock nut--M5 (1) --M5 (1) H Mounting bolt--M5 x 20 mm (1) --M5 x 20 (1) I Remote controller (1) (1) J Rubber cushion (1) (1) K Handles (2) (2) L Battery (1) (1) CR2025 See pages 35 and 36 of the INSTRUCTIONS for the usage of the following parts. 35 36. Additional standard plates (3) and transparent plate (1) (3) (1) Cutout plates (printed on the sheet) (4) ( ) (4) Hex screwdriver (1) (1) Spare screws for the plate cover attachment--M2 x 5 mm (2) --M2 x 5 (2) INSTALLATION (IN-DASH MOUNTING) The following illustration shows a typical installation. [. . . ] Notes: · Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC IN-CAR ENTERTAINMENT dealer. · It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 to 8 ). If the maximum power is less than 50 W, change "AMP GAIN" setting to prevent the speakers from being damaged (see page 34 of the INSTRUCTIONS). · To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape. · The heat sink becomes very hot after use. Be careful not to touch it when removing this unit. . · 50 ( , 4 8 ). 50 , "AMP GAIN" , (. . Heat sink PRECAUTIONS on power supply and speaker connections: · DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged. · BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car. : · , . · . + L- + - + L- + - + L- + - + R- + - + R- + - + R- + - 2 ENGLISH A Typical Connections / : . . Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color. 1 2 3 Connect the colored leads of the power cord in the order specified in the illustration below. Finally connect the wiring harness to the unit. 1 2 3 . . Note: If your vehicle does not have any accessory terminal, move the fuse from the fuse position 1 (initial position) to fuse position 2, and connect the red lead (A7) to the positive (+) battery terminal. · The yellow lead (A4) is not used in this case. : , 1 ( ) 2 (7) (+) . · (4) . B1 B2 B3 B4 B5 B6 A5 B7 B8 A7 A8 Fuse position 2 / 2 Fuse position 1 / 1 A2 A4 A6 Rear ground terminal B1 B2 B3 B4 B5 B6 A5 B7 B8 15 A fuse 15 A 15 1 A7 A8 *1 Not included for this unit *1 Ignition switch A2 A4 A6 Black Aerial terminal A8 *1 1 To metallic body or chassis of the car *1 2 Line out (see diagram (. ) ) 3 Yellow*2 *2 A4 2 To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V) ( ) ( 12 ) Red To CD changer or another external component (see diagram ) - (. [. . . ] . Rear speakers Remote lead Y-connector (not supplied with this unit) Y ( ) L R INPUT L R JVC Amplifier JVC- Remote lead (Blue with white stripe) ( ) *3 LINE OUT L R Signal cord (not supplied with this unit) ( ) L KD-SC607 R To the remote lead of other equipment or power aerial if any REAR FRONT Front speakers INPUT L R L R JVC Amplifier JVC- Front speakers *3 You can connect another power amplifier for front speakers. . *3 Firmly attach the ground wire to the metallic body or to the chassis of the car--to the place not *3 coated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do -- , ( , so may cause damage to the unit. . CD changer / - Refer also to page 38 of the INSTRUCTIONS. [. . . ]